1977L0540 — EN — 01.07.2013 — 008.001

---

This document is meant purely as a documentation tool and the institutions do not assume any liability for its contents

►B	COUNCIL DIRECTIVE of 28 June 1977 on the approximation of the laws of the Member States relating to parking lamps for motor vehicles (77/540/EEC) (OJ L 220, 29.8.1977, p.83)

Amended by:

		Official Journal
		No	page	date
M1	COUNCIL DIRECTIVE 87/354/EEC of 25 June 1987	L 192	43	11.7.1987
►M2	COMMISSION DIRECTIVE 1999/16/EC Text with EEA relevance of 16 March 1999	L 97	33	12.4.1999
►M3	COUNCIL DIRECTIVE 2006/96/EC of 20 November 2006	L 363	81	20.12.2006
►M4	COUNCIL DIRECTIVE 2013/15/EU of 13 May 2013	L 158	172	10.6.2013

Amended by:

A1		L 291	17	19.11.1979
A2		L 302	23	15.11.1985
A3		C 241	21	29.8.1994
		L 001	1	..
►A4		L 236	33	23.9.2003

Corrected by:

C1	Corrigendum, OJ L 284, 10.10.1978, p. 11  (1977/540)

---

▼B

COUNCIL DIRECTIVE

of 28 June 1977

on the approximation of the laws of the Member States relating to parking lamps for motor vehicles

(77/540/EEC)

Article 1

▼M2

1.  Each Member State shall grant EC component type-approval for any type of parking lamp which satisfies the construction and testing requirements laid down in the relevant Annexes.

▼B

2.  The Member State which has granted EEC component type-approval shall take the measures required in order to verify that production models conform to the approved type, in so far as this is necessary and if need be in cooperation with the competent authorities in the other Member States. Such verification shall be limited to spot checks.

Article 2

▼M2

Member States shall, for each type of parking lamp which they approve pursuant to Article 1, issue to the manufacturer an EC component type-approval mark conforming to the model shown in Annex I, Appendix 3.

▼B

Member States shall take all appropriate measures to prevent the use of marks liable to create confusion between parking lamps which have been type-approved pursuant to Article 1 and other devices.

Article 3

1.  No Member State may prohibit the placing on the market of parking lamps on grounds relating to their construction or method of functioning if they bear the EEC component type-approval mark.

2.  Nevertheless, a Member State may prohibit the placing on the market of parking lamps bearing the EEC component type-approval mark which consistently fail to conform to the approved type. That State shall inform the other Member States and the Commission forthwith of the measures taken, specifying the reasons for its decision.

▼M2

Article 4

The competent authorities of the Member States shall inform each other, by means of the procedures specified in Article 4(6) of Directive 70/156/EEC, of each approval which they have granted, refused or withdrawn pursuant to this Directive.

▼B

Article 5

1.  If the Member State which has granted EEC component type-approval finds that a number of parking lamps bearing the same EEC component type-approval mark do not conform to the type which it has approved, it shall take the necessary measures to ensure that production models conform to the approved type. The competent authorities of that State shall advise those of the other Member States of the measures taken which may, where there is consistent failure to conform, extend to withdrawal of EEC component type-approval. The said authorities shall take the same measures if they are informed by the competent authorities of another Member State of such failure to conform.

2.  The competent authorities of Member States shall inform each other within one month of any withdrawal of EEC component type-approval, and of the reasons for such a measure.

Article 6

Any decision taken pursuant to the provisions adopted in implementation of this Directive, to refuse or withdraw EEC component type-approval for a parking lamp or prohibit its placing on the market or use, shall set out in detail the reasons on which it is based. Such decisions shall be notified to the party concerned, who shall at the same time be informed of the remedies available to him under the laws in force in the Member States and of the time limits allowed for the exercise of such remedies.

Article 7

No Member State may refuse to grant EEC type-approval or national type-approval of a vehicle on grounds relating to its parking lamps if these bear the EEC component type-approval mark and are fitted in accordance with the requirements laid down in Directive 76/756/EEC.

Article 8

No Member State may refuse or prohibit the sale, registration, entry into service or use of any vehicle on grounds relating to its parking lamps if these bear the EEC component type-approval mark and are fitted in accordance with the requirements laid down in Directive 76/756/EEC.

▼M2

Article 9

For the purposes of this Directive, ‘vehicle’ means any motor vehicle intended for use on the road, with or without bodywork, having at least four wheels and a maximum design speed exceeding 25 km/h, and its trailers, with the exception of vehicles which run on rails and of agricultural and forestry tractors and all mobile machinery.

▼B

Article 10

Any amendments necessary to adjust the requirements of the Annexes to take account of technical progress shall be adopted in accordance with the procedure laid down in Article 13 of Directive 70/156/EEC.

Article 11

1.  Member States shall bring into force the provisions needed in order to comply with this Directive within 18 months of its notification and shall forthwith inform the Commission thereof.

2.  Member States shall ensure that the texts of the main provisions of national law which they adopt in the field covered by this Directive are communicated to the Commission.

Article 12

This Directive is addressed to the Member States.

▼M2

---

LIST OF ANNEXES

---

ANNEX I

ADMINISTRATIVE PROVISIONS FOR TYPE APPROVAL

1.   APPLICATION FOR EC COMPONENT TYPE-APPROVAL

1.1.	The application for EC component type-approval pursuant to Article 3(4) of Directive 70/156/EEC of a type of parking lamp shall be submitted by the manufacturer.

1.2.	A model for the information document is given in Appendix 1.

1.3.

The following must be submitted to the technical service responsible for conducting the type-approval tests: 1.3.1. Two samples, equipped with the lamp or lamps recommended; if the parking lamps are such that they can be mounted only on one side of the vehicle, the two samples submitted may be identical and be suitable for mounting only on the right or only on the left side of the vehicle.

2.   MARKINGS

2.1.

The devices submitted for EC component type approval must bear: 2.1.1. the trade name or mark of the manufacturer; 2.1.2. in the case of lamps with replaceable light sources: the type(s) of filament lamp prescribed; 2.1.3. in the case of lamps with non-replaceable light sources: the nominal voltage and wattage.

2.2.	These markings shall be clearly legible and indelible and shall be affixed to the illuminating surface, or to one of the illuminating surfaces, of the device. They shall be visible from the exterior when the device is fitted to the vehicle.

2.3.	Each device shall have sufficient space for the component type-approval mark. This space shall be indicated on the drawings referred to in Appendix 1.

3.   GRANTING OF EC COMPONENT TYPE-APPROVAL

4.   EC COMPONENT TYPE-APPROVAL MARK

4.1.	In addition to the markings referred to in item 2.1., every parking lamp conforming to the type approved pursuant to this Directive shall bear an EC component type-approval mark.

4.2.

This mark shall consist of: 4.2.1. a rectangle surrounding the letter ‘e’ followed by the distinguishing number or letters of the Member State which has granted type approval: 1 for Germany 2 for France 3 for Italy 4 for the Netherlands 5 for Sweden 6 for Belgium ▼A4 7 for Hungary 8 for the Czech Republic ▼M2 9 for Spain 11 for the United Kingdom 12 for Austria 13 for Luxembourg 17 for Finland 18 for Denmark ▼M3 19 for Romania ▼A4 20 for Poland ▼M2 21 for Portugal 23 for Greece ▼M4 25 for Croatia ▼A4 26 for Slovenia 27 for Slovakia 29 for Estonia 32 for Latvia ▼M3 34 for Bulgaria ▼A4 36 for Lithuania CY for Cyprus ▼M2 IRL for Ireland; ▼A4 MT for Malta; ▼M2 4.2.2. in the vicinity of the rectangle the ‘base approval number’ contained in section 4 of the type-approval number referred to in Annex VII of Directive 70/156/EEC, preceded by the two figures indicating the sequence number assigned to the most recent major technical amendment to Directive 77/540/EEC on the date EEC type-approval was granted. In this Directive the sequence number is 00; 4.2.3. when a lamp emits a light of amber colour towards the front and rear, the lamp must be marked with an arrow indicating its orientation, the arrow showing to the front of the vehicle.

4.3.	The EC component type-approval mark shall be affixed to the lens of the lamp or one of the lenses in such a way as to be indelible and clearly legible even when the lamps are fitted to the vehicle.

4.4.	An example of the EC component type-approval mark is given in Appendix 3.

4.5.

Where a single EC component type-approval number is issued, as per item 3.4. above, for a type of lighting and light-signalling device comprising a parking lamp and other lamps, a single EC component type-approval mark may be affixed, consisting of: 4.5.1. a rectangle surrounding the letter ‘e’ followed by the distinguishing number or letters of the Member State which has granted type approval (see item 4.2.1.); 4.5.2. the base approval number (see item 4.2.2., first half-sentence); 4.5.3. if necessary, the required arrow, in so far as it relates to the lamp assembly as a whole.

4.6.

This mark may be located anywhere on the lamps which are grouped, combined or reciprocally incorporated, provided that: 4.6.1. it is visible after the installation of the lamps; 4.6.2. no light-transmitting components of the grouped, combined or reciprocally incorporated lamps can be removed without simultaneously removing the approval mark.

4.7.

The identification symbol for each lamp corresponding to each Directive pursuant to which EC component type approval was granted, together with the sequence number (see item 4.2.2, second half-sentence) and, where necessary, the letter ‘D’ and the required arrow shall be marked: 4.7.1. either on the appropriate light-emitting surface; 4.7.2. or in a group, in such a way that each of the grouped, combined or reciprocally incorporated lamps may be clearly identified.

4.8.	The dimensions of the components of this mark must not be less than the minimum dimensions specified for individual marks by the various Directives pursuant to which EC component type approval was granted.

5.   MODIFICATIONS OF THE TYPE AND AMENDMENTS TO APPROVALS

6.   CONFORMITY OF PRODUCTION

---

Appendix 1

---

Appendix 2

---

Appendix 3

EXAMPLE OF THE EC COMPONENT TYPE-APPROVAL MARK

The device bearing the EC component type-approval mark shown above is a parking lamp, type approved in Germany (e1) pursuant to this Directive (00) under the base approval number 1471.

---

ANNEX II

TECHNICAL REQUIREMENTS

1.

The technical requirements are those set out in paragraphs 2, 6 to 9 and Annexes 3 to 5 of UN-ECE Regulation No 77 which consists of a consolidation of the following documents: — the Regulation in its original form (00) ( 6 ), — supplements 1 and 2 to Regulation No 77 including modifications ( 7 ), — supplement 3 to Regulation No 77 ( 8 ), — supplement 4 to Regulation No 77 ( 9 ), except that:

1.1.	Where reference is made to ‘Regulation No 48’, this shall be understood as ‘Directive 76/756/EEC’.

1.2.	Where reference is made to ‘Regulation No 37’, this shall be understood as ‘Annex VII to Directive 76/761/EEC.’

---

( 1 ) OJ No C 118, 16. 5. 1977, p. 29.

( 2 ) OJ No C 114, 11. 5. 1977, p. 4.

( 3 ) OJ No L 42, 23. 2. 1970, p. 1.

( 4 ) OJ No L 262, 27. 9. 1976, p. 1.

( 5 ) Of the documents referred to in point 1 of Annex II to this Directive.

(

6

) 

(

7

) 

(

8

) 

( 9 ) TRANS/WP.29/530