1.0.1 Unless otherwise stated, the authority, airport operator, air carrier or entity responsible in accordance with the national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 shall ensure the implementation of the measures set out in this chapter.

1.0.2 For the purposes of this chapter, an aircraft, bus, baggage cart or other means of transport, or a walkway or jetway, shall be regarded as a part of an airport.

For the purposes of this chapter, ‘secured baggage’ means screened departing hold baggage that is physically protected so as to prevent the introduction of any objects.

1.0.3 Without prejudice to the criteria for derogations as set in Regulation (EC) No 272/2009, the appropriate authority may allow special security procedures or exemptions for the protection and security of airside areas at airports on days on which there are not more than eight planned departing flights, provided that only one aircraft is to be loaded, unloaded, boarded or disembarked at any one time either within the critical part of the security restricted area or at an airport that falls outside of the scope of point 1.1.3.

1.1.1.1 Boundaries between landside, airside, security restricted areas, critical parts and, where applicable, demarcated areas shall be clearly identifiable at each airport in order to enable the appropriate security measures to be taken in each of those areas.

1.1.1.2 The boundary between landside and airside shall be a physical obstruction that is clearly visible to the general public and which denies a person unauthorised access.

1.1.2.1 Security restricted areas shall include at least the following:

1.1.2.2 A part of an airport shall be regarded as a security restricted area at least for the period of time that the activities referred to in point 1.1.2.1 are taking place.

When a security restricted area is established, a security search of the parts that could have been contaminated shall be carried out immediately before such an area is established in order to reasonably ensure that it does not contain prohibited articles. This provision shall be considered to be met for aircraft that are subject to an aircraft security search.

1.1.2.3 Whenever unauthorised persons may have had access to security restricted areas, a security search of the parts that could have been contaminated shall be carried out as soon as possible in order to reasonably ensure that it does not contain prohibited articles. This provision shall be considered to be met for aircraft that are subject to an aircraft security search.

1.1.3.1 Critical parts shall be established at airports where more than 40 persons hold airport identification cards giving access to security restricted areas.

1.1.3.2 Critical parts shall include at least the following:

A part of an airport shall be regarded as a critical part at least for the period of time that the activities referred to in (a) or (b) are taking place.

1.1.3.3 When a critical part is established, a security search of the parts that could have been contaminated shall be carried out immediately before such a part is established in order to reasonably ensure that it does not contain prohibited articles. This provision shall be considered to be met for aircraft that are subject to an aircraft security search.

1.1.3.4 Whenever unscreened persons may have had access to critical parts, a security search of the parts that could have been contaminated shall be carried out as soon as possible in order to reasonably ensure that it does not contain prohibited articles.

This provision shall be considered to be met for aircraft that are subject to an aircraft security search or check.

This provision shall not apply when persons covered by point 1.3.2 and point 4.1.1.7 have had access to these parts.

Persons arriving from third countries other than those listed in Attachment 4-B shall be considered to be unscreened persons.

1.2.1.1 Access to airside may only be authorised if persons and vehicles have a legitimate reason to be there.

1.2.1.2 In order to be granted access to airside a person shall carry an authorisation.

1.2.1.3 In order to be granted access to airside a vehicle shall display a vehicle pass.

1.2.1.4 Persons who are airside shall, upon request, present their authorisation for control.

1.2.2.1 Access to security restricted areas may only be granted if persons and vehicles have a legitimate reason to be there.

1.2.2.2 In order to be granted access to security restricted areas a person shall present one of the following authorisations:

1.2.2.3 In order to be granted access to security restricted areas a vehicle shall display a valid vehicle pass.

1.2.2.4 The boarding card or equivalent referred to in point 1.2.2.2(a) shall be checked before a person is granted access to security restricted areas in order to reasonably ensure that it is valid.

The card referred to in points 1.2.2.2(b) — (e), respectively, shall be checked before a person is granted access to security restricted areas in order to reasonably ensure that it is valid and corresponds to the holder.

1.2.2.5 In order to prevent unauthorised access to security restricted areas access points shall be controlled by:

1.2.2.6 The vehicle pass shall be checked before a vehicle is granted access to security restricted areas to ensure that it is valid and corresponds to the vehicle.

1.2.2.7 Access to security restricted areas shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.2.3.1 A crew identification card of a crew member employed by a Community air carrier and an airport identification card may only be issued to a person who has an operational need and has successfully completed a background check in accordance with point 11.1.3.

1.2.3.2 Crew and airport identification cards shall be issued for a period not exceeding five years.

1.2.3.3 The identification card of a person who fails a background check shall be immediately withdrawn.

1.2.3.4 The identification card shall be worn in a visible place at least whenever the holder is in security restricted areas.

A person who is not displaying his card in security restricted areas other than those areas where passengers are present shall be challenged by persons responsible for the implementation of point 1.5.1 (c) and, as appropriate, be reported.

1.2.3.5 The identification card shall be returned immediately to the issuing entity:

1.2.3.6 The issuing entity shall be notified immediately of the loss, theft or failure to return an identification card.

1.2.3.7 An electronic card shall be immediately disabled following return, expiry, withdrawal or notification of loss, theft or failure to return.

1.2.3.8 Community crew identification cards and airport identification cards shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.2.4.1 A crew identification card of a crew member employed by a Community air carrier shall display:

1.2.5.1 An airport identification card shall display:

The names and areas of access may be replaced by an equivalent identification.

1.2.5.2 In order to prevent the misuse of airport identification cards, a system shall be in place to reasonably ensure that attempted use of cards that have been lost, stolen or not returned is detected. Upon detection, appropriate action shall be taken.

1.2.6.1 A vehicle pass may only be issued where an operational need has been established.

1.2.6.2 A vehicle pass shall be specific to the vehicle and display:

Electronic vehicle passes need not display the areas for which the vehicle is authorised to have access nor the expiry date, provided that this information is electronically readable and checked before granting access to security restricted areas.

1.2.6.3 An electronic vehicle pass shall be fixed to the vehicle in a manner which ensures that it is non-transferable.

1.2.6.4 The vehicle pass shall be displayed in a visible place whenever the vehicle is airside.

1.2.6.5 The vehicle pass shall be returned immediately to the issuing entity:

1.2.6.6 The issuing entity shall be notified immediately of the loss, theft or failure to return a vehicle pass.

1.2.6.7 An electronic vehicle pass shall be immediately disabled following return, expiry or notification of loss, theft or failure to return.

1.2.6.8 In order to prevent the misuse of vehicle passes, a system shall be in place to reasonably ensure that attempted use of vehicle passes that have been lost, stolen or not returned is detected. Upon detection, appropriate action shall be taken.

1.2.7.1 Crew members, other than those holding a valid airport identification card, shall be escorted at all times when in security restricted areas other than:

1.2.7.2 Exceptionally, a person may be exempted from the requirements of point 1.2.5.1 and obligations on background checks on condition that he is escorted at all times when in security restricted areas.

1.2.7.3 An escort shall:

1.2.7.4 A vehicle may be exempted from the requirements of point 1.2.6 on condition that it is escorted at all times when airside.

1.3.1.1 The screening of persons other than passengers and items carried shall be performed in the same way as for passengers and cabin baggage, respectively.

1.3.1.2 Points 4.1.1.1 — 4.1.1.6 and 4.1.1.8 shall apply as regards the screening of persons other than passengers.

1.3.1.3 Points 4.1.2.1 — 4.1.2.9 and 4.1.2.12 shall apply as regards the screening of items carried by persons other than passengers.

1.3.1.4 Articles as listed in Attachment 4-C may be carried only if the person is authorised to do so in order to undertake tasks that are essential for the operation of airport facilities or of aircraft, or for performing in-flight duties.

1.3.1.5 Where persons other than passengers and items carried have to be screened on a continuous random basis, the frequency shall be established by the appropriate authority on the basis of a risk assessment.

1.3.1.6 The screening of persons other than passengers and items carried shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.3.2.1 The appropriate authority may, for objective reasons, allow persons other than passengers to be exempted from screening, or to be subjected to special screening procedures, provided that they are escorted by a person authorised to escort in accordance with point 1.2.7.3.

1.3.2.2 Screened persons other than passengers who temporarily leave critical parts may be exempted from screening on their return provided that they have been under constant observation by authorised persons sufficient to reasonably ensure that they do not introduce prohibited articles into those critical parts.

1.3.2.3 Exemptions and special screening procedures shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.4.1.1 All vehicles shall be examined before entering critical parts. They shall be protected from unlawful interference from after examination until entering critical parts.

1.4.1.2 The driver and any other occupants of the vehicle shall not be in the vehicle when the examination takes place. They shall be required to take their personal belongings out of the vehicle with them for screening.

1.4.1.3 There shall be defined methodologies to ensure the randomness of selection of the areas to be examined.

1.4.1.4 Vehicles entering critical parts shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.4.2.1 The driver and any other occupants of the vehicle shall not be in the vehicle when the examination takes place. They shall be required to take their personal belongings out of the vehicle with them for screening.

1.4.2.2 There shall be defined methodologies to ensure the randomness of selection of both vehicles and the areas to be examined.

1.4.2.3 Vehicles entering security restricted areas other than critical parts shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.4.3.1 A hand search shall consist of a thorough manual check of the areas selected, including contents, in order to reasonably ensure that they do not contain prohibited articles.

1.4.3.2 The following methods may only be used as a supplementary means of examination:

1.4.3.3 Methods of examination shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.4.4.1 The appropriate authority may, for objective reasons, allow vehicles to be exempted from examination, or to be subjected to special examination procedures, provided that they are escorted by a person authorised to escort in accordance with point 1.2.7.3.

1.4.4.2 Exemptions and special examination procedures shall also be subject to the additional provisions laid down in a separate Commission Decision.

1.5.1 Surveillance or patrols shall be undertaken in order to monitor:

1.5.2 The frequency and means of undertaking surveillance and patrols shall be based on a risk assessment undertaken by the appropriate authority, taking into account:

The parts of the risk assessment relating to the frequency and means of undertaking surveillance and patrols shall, upon request, be made available in writing for compliance monitoring purposes.

1.5.3 Surveillance and patrols shall not follow a predictable pattern. The validity of identification cards shall be checked on a random basis.

1.5.4 Measures shall be in place that both deter persons from breaching security checkpoints and, should such a breach occur, promptly enable the breach and its repercussions to be resolved and rectified.

3.0.1 Unless otherwise stated, an air carrier shall ensure the implementation of the measures set out in this chapter as regards its aircraft.

3.0.2 Third countries where the security standards applied are recognised as equivalent to the common basic standards as regards aircraft security are listed in Attachment 3-B.

3.0.3 An aircraft need not be subjected to an aircraft security check. It shall be subjected to an aircraft security search in accordance with point 3.1.

3.0.4 An air carrier shall, upon request, be notified by the airport operator whether or not its aircraft is in a critical part. When this is not clear, it shall be assumed that the aircraft is in a part other than a critical part.

3.0.5 When an area is no longer considered to be a critical part because of a change of security status then the airport shall inform those carriers that are affected.

3.1.1.1 An aircraft shall at all times be subjected to an aircraft security search whenever there is reason to believe that unauthorised persons may have had access to it.

3.1.1.2 An aircraft security search shall consist of an examination of defined areas of an aircraft that are laid down in a separate Commission Decision.

3.1.1.3 An aircraft arriving into a critical part from a third country not listed in Attachment 3-B shall be subjected to an aircraft security search any time after passenger disembarkation and/or the unloading of the hold.

3.1.1.4 An aircraft arriving from a Member State where it was in transit after having arrived from a third country not listed in Attachment 3-B shall be considered as an aircraft arriving from a third country.

3.1.1.5 When to perform an aircraft security search shall also be subject to the additional provisions laid down in a separate Commission Decision.

— flight number, and

— destination, and

— origin of the previous flight, and

— an indication whether or not an aircraft security search was completed.

— date and time that the aircraft security search was completed, and

— the name and signature of the person responsible for the performance of the aircraft security search.

3.2.1.1 Regardless of where an aircraft is parked at an airport, it shall be protected against unauthorised access by:

3.2.1.2 Point 3.2.1.1 shall not apply to an aircraft parked in a hangar that is locked or otherwise protected from unauthorised access.

3.2.2.1 Where external doors are closed and the aircraft is in a part other than a critical part, each external door shall also:

Point (a) shall not apply for a door that is accessible from the ground.

3.2.2.2 Where access aids are removed for doors that are not accessible from the ground, they shall be placed sufficiently far from the aircraft as to reasonably prevent access.

3.2.2.3 Where external doors are locked, only persons with an operational need shall be able to unlock these doors.

3.2.2.4 Where external doors are monitored, the monitoring shall ensure that unauthorised access to the aircraft is immediately detected.

3.2.2.5 The protection of aircraft with closed external doors in a part other than a critical part shall also be subject to the additional provisions laid down in a separate Commission Decision.

4.0.1 Unless otherwise stated, the authority, airport operator, air carrier or entity responsible in accordance with the national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 shall ensure the implementation of the measures set out in this chapter.

4.0.2 Third countries where the security standards applied are recognised as equivalent to the common basic standards as regards passengers and cabin baggage are listed in Attachment 4-B.

4.0.3 Passengers and their cabin baggage arriving from a Member State where the aircraft was in transit after having arrived from a third country not listed in Attachment 4-B shall be considered as passengers and cabin baggage arriving from a third country, unless there is a confirmation that these passengers and their cabin baggage were screened in that Member State.

4.0.4 For the purpose of this Annex:

4.1.1.1 Before screening, coats and jackets of passengers shall be taken off and shall be screened as cabin baggage.

4.1.1.2 Passengers shall be screened by:

▼M3

▼B

Where the screener cannot determine whether or not the passenger is carrying prohibited articles, the passenger shall be denied access to security restricted areas or rescreened to the screener’s satisfaction.

4.1.1.3 When a hand search is performed it shall be carried out so as to reasonably ensure that the person is not carrying prohibited articles.

4.1.1.4 When WTMD equipment alarms, the cause of the alarm shall be resolved.

4.1.1.5 Hand-held metal detection (HHMD) equipment may only be used as a supplementary means of screening. It shall not replace the requirements of a hand search.

4.1.1.6 Where a live animal is permitted to be carried in the cabin of an aircraft, it shall be screened either as a passenger or as cabin baggage.

4.1.1.7 The appropriate authority may create categories of passengers that, for objective reasons, shall be subject to special screening procedures or may be exempted from screening. The Commission shall be informed of the categories created.

4.1.1.8 The screening of passengers shall also be subject to the additional provisions laid down in a separate Commission Decision.

4.1.1.9 Explosive detection dogs may only be used as a supplementary means of screening.

4.1.2.1 Before screening, portable computers and other large electrical items shall be removed from cabin baggage and shall be screened separately.

4.1.2.2 Before screening, LAGs shall be removed from cabin baggage and shall be screened separately, unless the equipment used for the screening of cabin baggage is also capable of screening multiple closed LAG containers inside baggage.

Where LAGs have been removed from cabin baggage, the passenger shall present:

4.1.2.3 Cabin baggage shall be screened by:

▼M3

▼B

Where the screener cannot determine whether or not the cabin baggage contains any prohibited articles, it shall be rejected or rescreened to the screener’s satisfaction.

4.1.2.4 A hand search of cabin baggage shall consist of a manual check of the baggage, including its contents, as to reasonably ensure that it does not contain prohibited articles.

4.1.2.5 Where x-ray or EDS equipment is used, each image shall be viewed by the screener.

4.1.2.6 Where x-ray or EDS equipment is used, all alarms shall be resolved to the satisfaction of the screener so as to reasonably ensure that no prohibited articles are carried into the SRA or on board an aircraft.

4.1.2.7 Where x-ray or EDS equipment is used, any item whose density impairs the ability of the screener to analyse the contents of the cabin baggage shall be taken out of the baggage. The bag shall be screened again and the item shall be screened separately as cabin baggage.

4.1.2.8 Any bag that is found to contain a large electrical item shall be screened again with the item no longer in the bag and the electrical item screened separately.

4.1.2.9 Explosive detection dogs and explosive trace detection (ETD) equipment may only be used as a supplementary means of screening.

4.1.2.10 The appropriate authority may create categories of cabin baggage that, for objective reasons, shall be subject to special screening procedures or may be exempted from screening. The Commission shall be informed of the categories created.

4.1.2.11 The appropriate authority may allow a diplomatic bag to be exempted from screening or to be subjected to special security procedures provided that the requirements of the Vienna Convention on Diplomatic Relations are met.

4.1.2.12 The screening of cabin baggage shall also be subject to the additional provisions laid down in a separate Commission Decision.

4.1.3.1 LAGs shall be screened by:

4.1.3.2 Tasting or testing on the skin may be used as a supplementary means of screening.

4.1.3.3 The screening of LAGs shall also be subject to the additional provisions laid down in a separate Commission Decision.

4.1.3.4 LAGs carried by passengers may be exempted from screening if the LAG is:

4.3.1 An air carrier shall be notified in writing in advance by the competent authority of the plan to embark a potentially disruptive passenger on board its aircraft.

4.3.2 The notification shall contain the following details:

The air carrier shall make this information available to the pilot in command prior to passengers boarding the aircraft.

4.3.3 The competent authority shall ensure that persons in lawful custody are always escorted.

4.4.1 Passengers shall not be permitted to carry into security restricted areas or on board an aircraft the articles listed in Attachment 4-C.

4.4.2 An exemption to point 4.4.1. may be granted on condition that:

These articles shall then be placed in secure conditions on board aircraft.

4.4.3 The air carrier shall ensure that passengers are informed of the prohibited articles listed in Attachment 4-C before check-in is completed.

—  Canada:

— All international airports

—  Republic of Croatia:

—  Malaysia

— Kuala Lumpur International (KUL) airport

—  Republic of Singapore:

— Changi (SIN) airport

—  United States of America

— All international airports

5.0.1 Unless otherwise stated, the authority, airport operator, air carrier or entity responsible in accordance with the national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 shall ensure the implementation of the measures set out in this chapter.

5.0.2 Third countries where the security standards applied are recognised as equivalent to the common basic standards as regards hold baggage are listed in Attachment 5-A.

5.0.3 Hold baggage arriving from a Member State where the aircraft was in transit after having arrived from a third country not listed in Attachment 5-A shall be considered as hold baggage arriving from a third country, unless there is a confirmation that the hold baggage was screened in that Member State.

5.0.4 For the purpose of this chapter, ‘secured baggage’ means screened departing hold baggage that is physically protected so as to prevent the introduction of any objects.

5.1.1 The following methods, either individually or in combination, shall be used to screen hold baggage:

▼M3

▼B

Where the screener cannot determine whether or not the hold baggage contains any prohibited articles, it shall be rejected or rescreened to the screener’s satisfaction.

5.1.2 A hand search shall consist of a thorough manual check of the baggage, including all its contents, so as to reasonably ensure that it does not contain prohibited articles.

5.1.3 Where x-ray or EDS equipment is used, any item whose density impairs the ability of the screener to analyse the contents of the baggage shall result in it being subject to another means of screening.

5.1.4 Screening by explosive trace detection (ETD) equipment shall consist of the analysis of samples taken from both the inside and the outside of the baggage and from its contents. The contents may also be subjected to a hand search.

5.1.5 The appropriate authority may create categories of hold baggage that, for objective reasons, shall be subject to special screening procedures or may be exempted from screening. The Commission shall be informed of the categories created.

5.1.6 The screening of hold baggage shall also be subject to the additional provisions laid down in a separate Commission Decision.

5.2.1 Passengers may not be allowed access to screened hold baggage, unless it is their own baggage and they are supervised to ensure that:

5.2.2 Hold baggage that has not been protected from unauthorised interference shall be rescreened.

5.2.3 The protection of hold baggage shall also be subject to the additional provisions laid down in a separate Commission Decision.

5.3.1.1 An air carrier shall, during the boarding process, ensure that a passenger presents a valid boarding card or equivalent corresponding to the hold baggage that was checked in.

5.3.1.2 An air carrier shall ensure that there is a procedure in place to identify hold baggage of passengers who did not board or left the aircraft before departure.

5.3.1.3 If the passenger is not on board the aircraft, the hold baggage corresponding to his boarding card or equivalent shall be considered as unaccompanied.

5.3.1.4 An air carrier shall ensure that each item of unaccompanied hold baggage is clearly identifiable as authorised for transport by air.

5.3.2.1 The reason that the baggage became unaccompanied shall be recorded before it is loaded onto an aircraft, unless the security controls as referred to in point 5.3.3 are applied.

5.3.2.2 Additional detailed provisions on the factors beyond the passenger’s control are laid down in a separate Commission Decision.

5.3.3.1 Unaccompanied hold baggage not covered by point 5.3.2 shall be screened by one of the methods laid down in point 5.1.1 and, where applicable, applying additional requirements laid down in a separate Commission Decision.

5.3.3.2 Hold baggage that becomes unaccompanied baggage due to factors other than those mentioned in point 5.3.2 shall be rescreened after removal from the aircraft and before loading it again.

5.3.3.3 Additional detailed provisions for appropriate security controls for unaccompanied hold baggage are laid down in a separate Commission Decision.

5.4.1 Passengers shall not be permitted to carry in their hold baggage the articles listed in Attachment 5-B.

5.4.2 An exemption to point 5.4.1 may be granted on condition that:

5.4.3 Passengers shall be informed of the prohibited articles listed in Attachment 5-B before check-in is completed.

— ammunition,

— blasting caps,

— detonators and fuses,

— mines, grenades and other explosive military stores,

— fireworks and other pyrotechnics,

— smoke-generating canisters and smoke-generating cartridges,

— dynamite, gunpowder and plastic explosives.

6.0.1 The authority, airport operator, air carrier or entity as defined in this chapter shall ensure the implementation of the measures set out in this chapter.

6.0.2 The following shall be considered as prohibited articles in consignments of cargo:

6.0.3 The following shall be considered as prohibited articles in consignments of mail:

6.1.1 All cargo and mail shall be screened by a regulated agent before being loaded on to an aircraft, unless:

6.1.2 Where there is any reason to believe that a consignment to which security controls have been applied has been tampered with or has not been protected from unauthorised interference from the time that those controls were applied, it shall be screened by a regulated agent before being loaded on to an aircraft.

6.1.3 A person with unescorted access to identifiable air cargo or identifiable air mail to which the required security controls have been applied shall have successfully completed either a background check or a pre-employment check in accordance with point 11.1

6.2.1.1 When screening cargo or mail:

6.2.1.2 Where the screener cannot be reasonably sure that no prohibited articles are contained in the consignment, the consignment shall be rejected or be rescreened to his satisfaction.

6.2.1.3 The screening of cargo and mail shall also be subject to the additional provisions laid down in a separate Commission Decision.

6.3.1.1 Regulated agents shall be approved by the appropriate authority.

The approval as a regulated agent shall be site specific.

Any entity that applies security controls as referred to in point 6.3.2 shall be approved as a regulated agent. This includes third party logistics providers responsible for integrated warehousing and transportation services, air carriers and handling agents.

A regulated agent may subcontract:

6.3.1.2 The appropriate authority of each Member State shall define in its national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 the responsibilities for the implementation of the following procedure on the approval of regulated agents:

6.3.1.3 A regulated agent shall designate at least one person at each site who shall be responsible for the implementation of the submitted security programme. This person shall have successfully completed a background check in accordance with point 11.1.

6.3.1.4 A regulated agent shall be re-validated at regular intervals not exceeding 5 years. This shall include an on-site verification in order to assess whether the regulated agent still complies with the requirements of Regulation (EC) No 300/2008 and its implementing acts.

An inspection at the premises of the regulated agent by the appropriate authority in accordance with its national quality control programme may be considered as an on-site verification, provided that it covers all the requirements necessary for approval.

6.3.1.5 If the appropriate authority is no longer satisfied that the regulated agent complies with the requirements of Regulation (EC) No 300/2008 and its implementing acts, it shall withdraw the status of regulated agent for the specified site(s).

Immediately after withdrawal, and in all cases within 24 hours, the appropriate authority shall ensure that the agent’s change of status is indicated in the ‘EC database of regulated agents and known consignors’.

6.3.1.6 Without prejudice to the right of each Member State to apply more stringent measures in accordance with Article 6 of Regulation (EC) No 300/2008, a regulated agent approved in accordance with point 6.3 shall be recognised in all Member States.

6.3.1.7 The requirements of point 6.3.1, other than 6.3.1.2(d), shall not apply when the appropriate authority itself is to be approved as a regulated agent.

6.3.2.1 When accepting any consignments, a regulated agent shall establish whether the entity from which it receives the consignments is a regulated agent, a known consignor, an account consignor or none of these.

6.3.2.2 The person delivering the consignments to the regulated agent or air carrier shall present an identity card, passport, driving licence or other document, which includes his or her photograph and which has been issued or is recognised by the national authority. The card or document shall be used to establish the identity of the person delivering the consignments.

6.3.2.3 When accepting consignments to which not all required security controls have previously been applied, the regulated agent shall ensure that they are screened in accordance with point 6.2.

6.3.2.4 After the security controls referred to in points 6.3.2.1 to 6.3.2.3 of this Regulation and point 6.3 of a separate Commission Decision have been applied, the regulated agent shall ensure that:

6.3.2.5 After the security controls referred to in points 6.3.2.1 to 6.3.2.4 of this Regulation have been applied, the regulated agent shall ensure that any consignment tendered to an air carrier or another regulated agent is accompanied by appropriate documentation, either in the form of an air waybill or in a separate declaration and either in an electronic format or in writing.

6.3.2.6 The documentation shall be available for inspection by the appropriate authority at any point before the consignment is loaded on to an aircraft and shall provide the following information:

6.3.2.7 In the case of consolidations, the requirements under points 6.3.2.6(c), (e), (f) and (g) will be considered as met, if the regulated agent is able to establish the nature of the contents, the reason that the security status was issued and/or the name of the person who issued the security status and the date and time of issue, respectively, by a verifiable audit trail at any time before the consignment is loaded on an aircraft and afterwards for the duration of the flight or for 24 hours, whichever is the longer.

6.3.2.8 When accepting consignments to which not all required security controls have previously been applied, the regulated agent may also elect not to apply the security controls as referred to in point 6.3.2, but to hand the consignments over to another regulated agent to ensure the application of these security controls.

Security controls to be applied by a regulated agent shall also be subject to the additional provisions laid down in a separate Commission Decision.

6.4.1.1 Known consignors shall be approved by the appropriate authority.

The approval as a known consignor shall be site specific.

6.4.1.2 The appropriate authority of each Member State shall define in its national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 the responsibilities for the implementation of the following procedure on the approval of known consignors:

6.4.1.3 A known consignor shall designate at least one person at each site who shall be responsible for the application and supervision of the implementation of security controls at that site. This person shall have successfully completed a background check.

6.4.1.4 A known consignor shall be re-validated at regular intervals not exceeding 5 years. This shall include an on-site verification in order to assess whether the known consignor still complies with the requirements of Regulation (EC) No 300/2008 and its implementing acts.

An inspection at the premises of the known consignor by the appropriate authority in accordance with its national quality control programme may be considered as an on-site verification, provided that it covers all areas specified in the checklist of Attachment 6-C.

6.4.1.5 If the appropriate authority is no longer satisfied that the known consignor complies with the requirements of Regulation (EC) No 300/2008 and its implementing acts, it shall withdraw the status of known consignor for the specified site(s).

Immediately after withdrawal, and in all cases within 24 hours, the appropriate authority shall ensure that the consignor’s change of status is indicated in the ‘EC database of regulated agents and known consignors’.

6.4.1.6 Without prejudice to the right of each Member State to apply more stringent measures in accordance with Article 6 of Regulation (EC) No 300/2008, a known consignor approved in accordance with point 6.4 shall be recognised in all Member States.

Known consignors approved in accordance with point 6.4.1.2(d) shall also be subject to the additional provision laid down in point 6.4 of a separate Commission Decision.

6.4.2.1 A known consignor shall ensure that:

When, for whatever reason, these security controls have not been applied to a consignment, or where the consignment has not been originated by the known consignor for its own account, the known consignor shall clearly identify this to the regulated agent so that point 6.3.2.3 can be applied.

6.4.2.2 The known consignor shall accept that consignments to which the appropriate security controls have not been applied are screened in accordance with point 6.2.1.

6.5.1 Account consignors shall be designated by a regulated agent.

6.5.2 In order to be designated as an account consignor, the following procedure shall apply:

6.5.3 The regulated agent shall maintain a database with the information referred to in point 6.5.2(c). The database shall be available for inspection by the appropriate authority.

6.5.4 If there is no activity relating to movements of cargo or mail by air on the account of the account consignor within a period of 2 years, the status of account consignor shall expire.

6.5.5 If the appropriate authority or the regulated agent is no longer satisfied that the account consignor complies with the instructions as contained in Attachment 6-D, the regulated agent shall immediately withdraw the status of account consignor.

6.5.6 When, for whatever reason, the security controls specified in the ‘Aviation security instructions for account consignors’ have not been applied to a consignment, or where the consignment has not been originated by the account consignor for its own account, the account consignor shall clearly identify this to the regulated agent so that point 6.3.2.3 can be applied.

6.6.1.1 In order to ensure that consignments to which the required security controls have been applied are protected from unauthorised interference during transportation:

6.6.1.2 Point 6.6.1.1(b) (c) and (d) shall not apply during airside transportation.

6.6.2.1 Consignments of cargo and mail that are in a critical part shall be considered as protected from unauthorised interference.

6.6.2.2 Consignments of cargo and mail that are in a part other than a critical part shall be considered as protected from unauthorised interference if:

— to the best of my knowledge, the information contained in the company’s security programme is true and accurate,

— the practices and procedures set out in this security programme will be implemented and maintained at all sites covered by the programme,

— this security programme will be adjusted and adapted to comply with all future relevant changes to EC legislation, unless [name of company] informs [name of appropriate authority] that it no longer wishes to trade as a regulated agent,

— [name of company] will inform [name of appropriate authority] in writing of:

— in order to ensure compliance with relevant EC legislation, [name of company] will cooperate fully with all inspections, as required, and provide access to all documents, as requested by inspectors,

— [name of company] will inform [name of appropriate authority] of any serious security breaches and of any suspicious circumstances which may be relevant to air cargo/air mail security, in particular any attempt to conceal prohibited articles in consignments,

— [name of company] will ensure that all relevant staff receive appropriate training and are aware of their security responsibilities under the company’s security programme, and

— [name of company] will inform [name of appropriate authority] if:

(a) the consignments shall be sealed before transportation; and

(b) the haulier declaration as contained in Attachment 6-E shall be agreed by the haulier who transports on behalf of the account consignor.

(a) they are separated from consignments which it has originated; and

(b) the origin is clearly indicated on the consignment or on accompanying documentation.

— [name of company] complies with these ‘Aviation security instructions for account consignors’,

— [name of company] ensures that these instructions are communicated to staff with access to air cargo/air mail,

— [name of company] keeps air cargo/air mail secure until it is handed over to the regulated agent,

— [name of company] accepts that consignments may be subject to security controls, including screening, and

— [name of company] accepts unannounced inspections at its premises by the appropriate authority of the Member State in which it is located in order to assess whether [name of company] complies with these instructions.

— all staff who transport this air cargo/mail will have received security awareness training,

— the integrity of all staff being recruited with access to this air cargo/mail will be verified. This verification shall include at least a check of the identity (if possible by photographic identity card, driving licence or passport) and a check of the curriculum vitae and/or provided references,

— load compartments in vehicles will be sealed or locked. Curtain sided vehicles will be secured with TIR cords. The load areas of flat bed trucks will be kept under observation when air cargo is being transported,

— immediately prior to loading, the load compartment will be searched and the integrity of this search maintained until loading is completed,

— each driver will carry an identity card, passport, driving licence or other document, containing a photograph of the person, which has been issued or recognised by the national authorities,

— drivers will not make unscheduled stops between collection and delivery. Where this is unavoidable, the driver will check the security of the load and the integrity of locks and/or seals on his return. If the driver discovers any evidence of interference, he will notify his supervisor and the air cargo/mail will not be delivered without notification at delivery,

— transport will not be sub-contracted to a third party, unless the third party also has a haulier agreement with [same name as above of regulated agent/known consignor/account consignor, or of the appropriate authority which has approved or certified the haulier], and

— no other services (e.g. storage) will be sub-contracted to any other party other than a regulated agent or an entity that has been certified or approved and listed for the provision of these services by the appropriate authority.

7.1.1 Before being loaded into the hold of an aircraft, air carrier mail and air carrier materials shall either be screened and protected in accordance with chapter 5 or be subjected to security controls and protected in accordance with chapter 6.

7.1.2 Before being loaded into any part of an aircraft other than the hold, air carrier mail and air carrier materials shall be screened and protected in accordance with the provisions on cabin baggage in chapter 4.

7.1.3 Air carrier mail and air carrier materials to be loaded onto an aircraft shall also be subject to the additional provisions laid down in a separate Commission Decision.

7.2.1 Air carrier materials which are used for the purposes of passenger and baggage processing and which could be used to compromise aviation security shall be protected or kept under surveillance in order to prevent unauthorised access.

Self check-in and applicable Internet options allowed for use by passengers shall be considered as authorised access to such materials.

7.2.2 Discarded materials which could be used to facilitate unauthorised access or move baggage into the security restricted area or onto aircraft shall be destroyed or invalidated.

7.2.3 Departure control systems and check-in systems shall be managed in such a manner as to prevent unauthorised access.

Self check-in allowed for use by passengers shall be considered as authorised access to such systems.

8.0.1 Unless otherwise stated, the authority, airport operator, air carrier or entity responsible in accordance with the national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 shall ensure the implementation of the measures set out in this chapter.

8.0.2 For the purpose of this chapter, ‘in-flight supplies’ means all items intended to be taken on board an aircraft for use, consumption or purchase by passengers or crew during a flight, other than:

For the purpose of this chapter, ‘regulated supplier of in-flight supplies’ means a supplier whose procedures meet common security rules and standards sufficient to allow delivery of in-flight supplies directly to aircraft.

For the purpose of this chapter, ‘known supplier of in-flight supplies’ means a supplier whose procedures meet common security rules and standards sufficient to allow delivery of in-flight supplies to an air carrier or regulated supplier, but not directly to aircraft.

8.0.3 Supplies shall be considered as in-flight supplies from the time that they are identifiable as supplies to be taken on board an aircraft for use, consumption or purchase by passengers or crew during a flight.

8.1.1.1 In-flight supplies shall be screened before being taken into a security restricted area, unless:

8.1.1.2 Any in-flight supply received from a regulated supplier or a known supplier that shows signs of being tampered with, or where there is reason to believe that it has not been protected from unauthorised interference from the time that controls were applied, shall be screened.

8.1.1.3 The security controls of in-flight supplies shall also be subject to the additional provisions laid down in a separate Commission Decision.

8.1.2.1 When screening in-flight supplies, the means or method employed shall take into consideration the nature of the supplies and shall be of a standard sufficient to reasonably ensure that no prohibited articles are concealed in the supplies.

8.1.2.2 The screening of in-flight supplies shall also be subject to the additional provisions laid down in a separate Commission Decision.

8.1.3.1 Regulated suppliers shall be approved by the appropriate authority.

The approval as a regulated supplier shall be site specific.

Any entity that ensures the security controls as referred to in point 8.1.5 and delivers in-flight supplies directly to aircraft shall be approved as a regulated supplier. This shall not apply to an air carrier that applies these security controls itself and delivers supplies only to its own aircraft.

8.1.3.2 The appropriate authority of each Member State shall define in its national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 the responsibilities for the implementation of the following procedure on the approval of regulated suppliers:

8.1.3.3 A regulated supplier shall be re-validated at regular intervals not exceeding 5 years. This shall include an on-site verification in order to assess whether the regulated supplier still complies with the requirements of point 8.1.5.

An inspection at the premises of the regulated supplier by the appropriate authority in accordance with its national quality control programme may be considered as an on-site verification, provided that it covers all the requirements of point 8.1.5.

8.1.3.4 If the appropriate authority is no longer satisfied that the regulated supplier complies with the requirements of point 8.1.5, it shall withdraw the status of regulated supplier for the specified sites.

8.1.3.5 Without prejudice to the right of each Member State to apply more stringent measures in accordance with Article 6 of Regulation (EC) No 300/2008, a regulated supplier approved in accordance with point 8.1.3 shall be recognised in all Member States.

8.1.4.1 Any entity that ensures the security controls as referred to in point 8.1.5.1 and delivers in-flight supplies, but not directly to aircraft, shall be designated as a known supplier by the company to whom it delivers. This shall not apply to a regulated supplier.

8.1.4.2 In order to be designated as a known supplier, the entity shall submit the ‘Declaration of commitments — known supplier of in-flight supplies’ as contained in Attachment 8-B to each company to whom it delivers. This declaration shall be signed by the legal representative or by the person responsible for security.

The signed declaration shall be retained by the company to whom the known supplier delivers as a means of validation.

8.1.4.3 If there are no deliveries within a period of 2 years, the status of known supplier shall expire.

8.1.4.4 If the appropriate authority or the company to whom the known supplier delivers is no longer satisfied that the known supplier complies with the requirements of point 8.1.5.1, the company concerned shall withdraw the status of known supplier.

8.1.5.1 An air carrier, a regulated supplier and a known supplier of in-flight supplies shall:

Point (e) shall not apply during airside transportation.

8.1.5.2 The security controls to be applied by an air carrier and a regulated supplier shall also be subject to the additional provisions laid down in a separate Commission Decision.

1. In-flight supplies of STEBs shall be delivered in tamper-evident packaging to an airside area or to a security restricted area.

2. After first reception on airside or in a security restricted area and until their final sale on the aircraft, LAGs and STEBs shall be protected from unauthorised interference.

3. Detailed provisions for the additional security provisions for in-flight supplies of LAGs and STEBs are laid down in a separate Decision.

— to the best of my knowledge, the information contained in the company’s security programme is true and accurate,

— the practices and procedures set out in this security programme will be implemented and maintained at all sites covered by the programme,

— this security programme will be adjusted and adapted to comply with all future relevant changes to EC legislation, unless [name of company] informs [name of appropriate authority] that it no longer wishes to deliver in-flight supplies directly to aircraft (and thus no longer wishes to trade as a regulated supplier),

— [name of company] will inform [name of appropriate authority] in writing of:

— in order to ensure compliance with relevant EC legislation, [name of company] will cooperate fully with all inspections, as required, and provide access to all documents, as requested by inspectors,

— [name of company] will inform [name of appropriate authority] of any serious security breaches and of any suspicious circumstances which may be relevant to in-flight supplies, in particular any attempt to conceal prohibited articles in supplies,

— [name of company] will ensure that all relevant staff receive appropriate training and are aware of their security responsibilities under the company’s security programme, and

— [name of company] will inform [name of appropriate authority] if:

— [name of company] complies with the requirements of EC legislation,

— in order to ensure compliance with relevant EC legislation, [name of company] will cooperate fully with all inspections, as required, and provide access to all documents, as requested by inspectors,

— [name of company] will inform [the air carrier or regulated supplier to whom it delivers in-flight supplies] of any serious security breaches and of any suspicious circumstances which may be relevant to in-flight supplies, in particular any attempt to conceal prohibited articles in supplies,

— [the company] will ensure that all relevant staff receive appropriate training and are aware of their security responsibilities, and

— [name of company] will inform [the air carrier or regulated supplier to whom it delivers in-flight supplies] if:

9.0.1 Unless otherwise stated or unless the implementation of screening is ensured by an authority or entity, an airport operator shall ensure the implementation of the measures set out in this chapter.

9.0.2 For the purpose of this chapter,

9.0.3 Supplies shall be considered as airport supplies from the time that they are identifiable as supplies to be sold, used or made available in security restricted areas of airports.

9.1.1.1 Airport supplies shall be screened before being allowed into security restricted areas, unless security controls have been applied to the supplies by a known supplier and the supplies have been protected from unauthorised interference from the time that those controls were applied until they are taken into the security restricted area.

9.1.1.2 Airport supplies which originate in the security restricted area may be exempted from these security controls.

9.1.1.3 Any airport supply received from a known supplier that shows signs of being tampered with, or where there is reason to believe that it has not been protected from unauthorised interference from the time that controls were applied, shall be screened.

9.1.1.4 Upon delivery at the outlet in the security restricted area, a visual check of the airport supplies shall be carried out by the staff of the outlet in order to ensure that there are no signs of tampering.

9.1.2.1 When screening airport supplies, the means or method employed shall take into consideration the nature of the supply and shall be of a standard sufficient to reasonably ensure that no prohibited articles are concealed in the supply.

9.1.2.2 The screening of airport supplies shall also be subject to the additional provisions laid down in a separate Commission Decision.

9.1.3.1 Any entity that ensures the security controls as referred to in point 9.1.4 and delivers airport supplies shall be designated as a known supplier by the airport operator.

9.1.3.2 In order to be designated as a known supplier, the entity shall submit the ‘Declaration of commitments — known supplier of airport supplies’ as contained in Attachment 9-A to the airport operator. This declaration shall be signed by the legal representative or by the person responsible for security.

The signed declaration shall be retained by the airport operator as a means of validation.

9.1.3.3 If there are no deliveries within a period of 2 years, the status of known supplier shall expire.

9.1.3.4 If the appropriate authority or the airport operator is no longer satisfied that the known supplier complies with the requirements of point 9.1.4, the airport operator shall withdraw the status of known supplier.

(a) appoint a person responsible for security in the company; and

(b) ensure that persons with access to airport supplies receive security awareness training before being given access to these supplies; and

(c) prevent unauthorised access to its premises and airport supplies; and

(d) reasonably ensure that no prohibited articles are concealed in airport supplies; and

(e) apply tamper-evident seals to, or physically protect, all vehicles and/or containers that transport airport supplies.

1. Supplies of STEBs shall be delivered in tamper-evident packaging to an airside area beyond the point where boarding passes are controlled or to a security restricted area.

2. After first reception on airside or in a security restricted area and until their final sale at the outlet, LAGs and STEBs shall be protected against unauthorised interference.

3. Detailed provisions for the additional security provisions for supplies of LAGs and STEBs are laid down in a separate Decision.

— [name of company] complies with the requirements of EC legislation,

— in order to ensure compliance with relevant EC legislation, [name of company] will cooperate fully with all inspections, as required, and provide access to all documents, as requested by inspectors,

— [name of company] will inform [the appropriate authority and airport operator] of any serious security breaches and of any suspicious circumstances which may be relevant to airport supplies, in particular any attempt to conceal prohibited articles in supplies,

— [the company] will ensure that all relevant staff receive appropriate training and are aware of their security responsibilities, and

— [name of company] will inform [the airport operator] if:

11.0.1 The authority, airport operator, air carrier or entity deploying persons implementing, or responsible for implementing, measures for which it is responsible in accordance with the national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 shall ensure that these persons meet the standards set out in this chapter.

11.0.2 For the purpose of this chapter, ‘certification’ means a formal evaluation and confirmation by or on behalf of the appropriate authority indicating that the person has successfully completed the relevant training and that the person possesses the necessary competencies to perform assigned functions to an acceptable level.

11.0.3 For the purposes of this chapter, a ‘state of residence’ shall be any country in which the person has been resident continuously for 6 months or more and a ‘gap’ in the record of education or employment shall mean any gap of more than 28 days.

11.0.4 Competencies acquired by persons prior to recruitment may be taken into consideration when assessing any training needs under this section.

11.1.1 Persons being recruited to implement, or to be responsible for the implementation of, screening, access control or other security controls in a security restricted area shall have successfully completed a background check.

11.1.2 Persons being recruited to implement, or to be responsible for the implementation of, screening, access control or other security controls elsewhere than a security restricted area shall have successfully completed a background or pre-employment check. Unless otherwise specified in this Regulation, whether a background or pre-employment check has to be completed shall be determined by the appropriate authority in accordance with applicable national rules.

11.1.3 In accordance with Community and national rules, a background check shall at least:

11.1.4 In accordance with Community and national rules, a pre-employment check shall:

11.1.5 Background or pre-employment checks shall be completed before the person undergoes any security training involving access to information which is not publicly available.

11.1.6 The recruitment process for all persons being recruited under points 11.1.1 and 11.1.2 shall include at least a written application and an interview stage designed to provide an initial assessment of abilities and aptitudes.

11.1.7 Persons being recruited to implement security controls shall have the mental and physical abilities and aptitudes required to carry out their designated tasks effectively and shall be made aware of the nature of these requirements at the outset of the recruitment process.

These abilities and aptitudes shall be assessed during the recruitment process and before completion of any probationary period.

11.1.8 Recruitment records, including results of any assessment tests, shall be kept for all persons recruited under points 11.1.1 and 11.1.2 for at least the duration of their contract.

11.2.1.1 Persons shall have successfully completed relevant training before being authorised to implement security controls unsupervised.

11.2.1.2 Training of persons performing tasks as listed in points 11.2.3.1 to 11.2.3.5 and point 11.2.4 shall include theoretical, practical and on-the-job training elements.

11.2.1.3 The content of courses shall be specified or approved by the appropriate authority before:

Computer based training may be used with or without the support of an instructor or coach.

11.2.1.4 Training records shall be kept for all persons trained for at least the duration of their contract.

(a) knowledge of previous acts of unlawful interference with civil aviation, terrorist acts and current threats;

(b) knowledge of the legal framework for aviation security;

(c) knowledge of the objectives and organisation of aviation security, including the obligations and responsibilities of persons implementing security controls;

(d) knowledge of access control procedures;

(e) knowledge of identification card systems used at the airport;

(f) knowledge of procedures for challenging persons and of circumstances in which persons should be challenged or reported;

(g) knowledge of reporting procedures;

(h) ability to identify prohibited articles;

(i) ability to respond appropriately to security related incidents;

(j) knowledge of how human behaviour and responses can affect security performance; and

(k) ability to communicate clearly and confidently.

11.2.3.1 Job specific training of persons implementing screening of persons, cabin baggage, items carried and hold baggage shall result in the following competencies:

11.2.3.2 Training of persons implementing screening of cargo and mail shall result in the following competencies:

11.2.3.3 Training of persons implementing screening of air carrier mail and materials, in-flight supplies and airport supplies shall result in the following competencies:

11.2.3.4 Specific training of persons performing vehicle examinations shall result in the following competencies:

11.2.3.5 Specific training of persons implementing access control at an airport as well as surveillance and patrols shall result in the following competencies:

11.2.3.6 Training of persons implementing aircraft security searches shall result in the following competencies:

11.2.3.7 Training of persons implementing aircraft protection shall result in the following competencies:

11.2.3.8 Training of persons implementing baggage reconciliation shall result in the following competencies:

11.2.3.9 Training of persons implementing security controls for cargo and mail other than screening, or having access to identifiable air cargo or identifiable air mail, shall result in the following competencies:

11.2.3.10 Training of persons implementing security controls for air carrier mail and materials, in-flight supplies and airport supplies other than screening shall result in the following competencies:

(a) knowledge of the relevant legal requirements and how they should be met;

(b) knowledge of supervisory tasks;

(c) knowledge of internal quality control;

(d) ability to respond appropriately to the detection of prohibited articles;

(e) knowledge of emergency response procedures;

(f) ability to provide mentoring and on-the-job training and to motivate others;

and, where the person’s designated tasks so require:

(g) knowledge of conflict management; and

(h) knowledge of the capabilities and limitations of security equipment or screening methods used.

(a) knowledge of the relevant legal requirements and how they should be met;

(b) knowledge of internal, national, Community and international quality control;

(c) ability to motivate others;

(d) knowledge of the capabilities and limitations of security equipment or screening methods used.

11.2.6.1 Persons other than passengers requiring unescorted access to security restricted areas and not falling under points 11.2.3 to 11.2.5 and 11.5 shall receive security awareness training before being issued with an authorisation granting unescorted access to security restricted areas.

11.2.6.2 Security awareness training shall result in the following competencies:

11.2.6.3 Each person undergoing security awareness training shall be required to demonstrate understanding of all subjects referred to in point 11.2.6.2 before being issued with an authorisation granting unescorted access to security restricted areas.

11.3.1 Persons performing tasks as listed in points 11.2.3.1. to 11.2.3.5 shall be subject to:

11.3.2 Persons operating x-ray or EDS equipment shall, as part of the initial certification or approval process, pass a standardised image interpretation test.

11.3.3 The recertification or re-approval process for persons operating x-ray or EDS equipment shall include both the standardised image interpretation test and an evaluation of operational performance.

11.3.4 Failure to undertake and successfully complete recertification or re-approval within a reasonable timescale, not normally exceeding 3 months, shall result in the related security entitlements being withdrawn.

11.3.5 Certification or approval records shall be kept for all persons certified or approved, respectively, for at least the duration of their contract.

11.4.1 Persons operating x-ray or EDS equipment shall be subject to recurrent training consisting of image recognition training and testing. This shall take the form of:

The results of testing shall be provided to the person and recorded and may be taken into consideration as part of the recertification or re-approval process.

For classroom and/or computer based training, persons shall be subject to image recognition training and testing for at least 6 hours in every 6 month period. An image library shall be used containing at least 1 000 images of at least 250 different threat articles, including images of component parts of threat articles, with each article captured in a variety of different orientations. There shall be an unpredictable selection of images from the library during the training and testing.

For on-the-job TIP training, the TIP library shall consist of at least 6 000 images of at least 1 500 different threat articles, including images of component parts of threat articles, with each article captured in a variety of different orientations.

11.4.2 Persons performing tasks as listed under point 11.2 other than those referred to in point 11.4.1 shall undergo recurrent training at a frequency sufficient to ensure that competencies are maintained and acquired in line with security developments.

Recurrent training shall be conducted:

The requirements under (a) shall not apply to competencies acquired during specific training which are no longer required for the person’s designated tasks.

11.4.3 Records of recurrent training shall be kept for all persons trained for at least the duration of their contract.

11.5.1 The appropriate authority shall maintain or have access to lists of certified instructors and, if appropriate, independent validators who have met the requirements set out in point 11.5.2, 11.5.3 or 11.5.4.

11.5.2 Instructors and independent validators shall have successfully completed a background check in accordance with point 11.1.3 and produce evidence of relevant qualifications or knowledge. Independent validators shall be free from any contractual or pecuniary obligation to the airport operators, air carriers or entities they are recruited to monitor.

11.5.3 Instructors who were recruited or who were providing training specified in this Regulation before it came into force shall, as a minimum, satisfy the appropriate authority that they:

11.5.4 Independent validators who were recruited before this Regulation came into force shall, as a minimum, satisfy the appropriate authority that they:

11.5.5 In order to be certified as an instructor qualified to give training defined in points 11.2.3.1 to 11.2.3.5 and in points 11.2.4 and 11.2.5, a person shall have knowledge of the work environment in the relevant aviation security field and qualifications and competencies in the following areas:

11.5.6 In order to be certified as an independent validator, a person shall have knowledge of the work environment in the relevant aviation security field and competencies in the following areas:

11.5.7 The appropriate authority shall either itself provide training for instructors and independent validators or approve and maintain a list of appropriate security training courses. The appropriate authority shall ensure that instructors and independent validators receive regular training or information on developments in the relevant fields.

11.5.8 Where the appropriate authority is no longer satisfied that training delivered by a qualified instructor is resulting in the relevant competencies, the appropriate authority shall either withdraw approval of the course or ensure that the trainer is suspended or removed from the list of qualified instructors, as appropriate.

12.0.1 The authority, operator or entity using equipment for the implementation of measures for which it is responsible in accordance with the national civil aviation security programme as referred to in Article 10 of Regulation (EC) No 300/2008 shall take reasonable steps to ensure that the equipment meets the standards set out in this chapter.

The information classified in accordance with Commission Decision 2001/844/EC, ECSC, Euratom ( 10 ) shall be made available by the appropriate authority to manufacturers on a need-to-know basis.

12.0.2 There shall be routine testing of each piece of security equipment.

12.1.1.1 Walk-through metal detection equipment (WTMD) shall be able to detect and to indicate by means of an alarm at least specified metallic items, both individually and in combination.

12.1.1.2 The detection by WTMD shall be independent of the position and orientation of the metallic item.

12.1.1.3 WTMD shall be firmly fixed to a solid base.

12.1.1.4 WTMD shall have a visual indicator to show that the equipment is in operation.

12.1.1.5 The means for adjusting the detection settings of WTMD shall be protected and accessible only to authorised persons.

12.1.1.6 WTMD shall give both a visual alarm and an audible alarm when it detects metallic items as referred to in point 12.1.1.1. Both types of alarm shall be noticeable at a range of 2 metres.

12.1.1.7 The visual alarm shall give an indication of the strength of signal detected by the WTMD.

12.1.1.8 WTMD shall be positioned so as to ensure it is not affected by sources of interference.

12.1.2.1 There shall be two standards for WTMD. Detailed requirements on these standards are laid down in a separate Commission Decision.

12.1.2.2 All WTMD shall meet standard 1.

Standard 1 shall expire on 1 January 2011.

12.1.2.3 Standard 2 shall apply to WTMD installed as from 5 January 2007, unless a contract to install WTMD that meets standard 1 has already been placed before this date.

All WTMD shall meet standard 2 by 1 January 2011.

(a) generate an audible and/or visual signal on a percentage of persons passing through the WTMD who did not cause an alarm as referred to in point 12.1.1.1. It shall be possible to set the percentage; and

(b) count the number of persons screened, excluding any person that passes through the WTMD in the opposite direction; and

(c) count the number of alarms; and

(d) calculate the number of alarms as a percentage of the number of screened persons.

12.2.1 Hand-held metal detection equipment (HHMD) shall be able to detect ferrous and non-ferrous metallic items. Detection and identification of the position of the detected metal shall be indicated by means of an alarm.

12.2.2 The means for adjusting the sensitivity settings of HHMD shall be protected and accessible only to authorised persons.

12.2.3 HHMD shall give an audible alarm when it detects metallic items. The alarm shall be noticeable at a range of 1 metre.

12.2.4 The performance of HHMD shall not be affected by sources of interference.

12.2.5 HHMD shall have a visual indicator to show that the equipment is in operation.

12.4.1.1 Explosive detection systems equipment (EDS) shall be able to detect and to indicate by means of an alarm specified and higher individual quantities of explosive material contained in baggage or other consignments.

12.4.1.2 The detection shall be independent of the shape, position or orientation of the explosive material.

12.4.1.3 EDS shall give an alarm in each of the following circumstances:

12.4.2.1 There shall be three standards for EDS. Detailed requirements on these standards are laid down in a separate Commission Decision.

12.4.2.2 All EDS shall meet standard 1.

Standard 1 shall expire on 1 September 2012.

The appropriate authority may permit standard 1 EDS installed between 1 January 2003 and 1 September 2006 to continue to be used until 1 January 2014 at the latest.

12.4.2.3 Standard 2 shall apply to all EDS installed as from 1 January 2007, unless a contract to install EDS that meets standard 1 has been placed before 19 October 2006.

All EDS shall meet standard 2 by 1 September 2012 at the latest, unless the third subparagraph of point 12.4.2.2 applies.

Standard 2 shall expire on 1 September 2018.

12.4.2.4 Standard 3 shall apply to all EDS installed as from 1 September 2012.

All EDS shall meet standard 3 by 1 September 2018 at the latest.

12.5.1.1 Threat image projection (TIP) shall be able to project virtual images of threat articles within the x-ray image of bags or other consignments being screened.

The virtual images shall be placed within the x-ray image of bags and consignments being screened in an evenly distributed manner and not in a fixed position.

It shall be possible to set the percentage of virtual images to be projected.

12.5.1.2 TIP shall not impair the performance and normal functioning of x-ray equipment.

No indication shall be given to the screener that a virtual image of a threat article is about to be projected or has been projected until a message is presented in accordance with point 12.5.2.2.

12.5.1.3 The means for managing TIP shall be protected and accessible only to authorised persons.

12.5.2.1 TIP shall comprise of at least:

12.5.2.2 TIP shall present a message to the screener:

The message shall be presented so that it does not obscure the image of the bag or consignment to which it refers.

The message shall remain until it has been cleared by the screener. In the case of points (a) and (b) the message shall be presented together with the virtual image of the threat article.

12.5.2.3 Access to equipment with TIP installed and deployed shall require that the screener uses a unique identifier.

12.5.2.4 TIP shall be able to store the results of the responses of individual screeners for a minimum of 12 months and in a format to allow the provision of reports.

12.5.2.5 The composition of TIP shall also be subject to the additional detailed requirements laid down in a separate Commission Decision.

12.7.1.1 Equipment listed in point 4.1.3.1 that is used for the screening of liquids, aerosols and gels (LAGs) shall be able to detect and to indicate by means of an alarm specified and higher individual quantities of threat materials in LAGs.

12.7.1.2 The detection shall be independent of the shape or material of the LAG container.

12.7.1.3 The equipment shall be used in a manner that ensures that the container is positioned and orientated so as to ensure that the detection capabilities are met in full.

12.7.1.4 The equipment shall give an alarm in each of the following circumstances:

12.7.2.1 There shall be two standards for equipment for the screening of LAGs. Detailed requirements on these standards are laid down in a separate Commission Decision.

12.7.2.2 All equipment for the screening of LAGs shall meet standard 1.

Standard 1 shall expire on 28 April 2014.

12.7.2.3 Standard 2 shall apply to all equipment for the screening of LAGs installed as from 29 April 2014.

All equipment for the screening of LAGs shall meet standard 2 by 29 April 2016 at the latest.

12.8.1 A Member State may allow a method of screening using new technologies other than those laid down in this Regulation, provided that:

12.8.2 At least four months before its planned introduction the Member State concerned shall inform in writing the Commission and the other Member States of the proposed method of screening it intends to allow, enclosing an assessment indicating how it shall guarantee that the application of the new method will meet the requirement of point 12.8.1.(b). The notification shall also contain detailed information on the location(s) where the method of screening is planned to be used and the intended length of the evaluation period.

12.8.3 If the Commission gives the Member State a positive reply, or if no reply is received within three months upon receipt of the written request, the Member State may then allow the introduction of the method of screening using new technologies.

If the Commission is not satisfied that the proposed method of screening provides sufficient guarantees that the overall level of aviation security will be maintained in the Community, the Commission shall inform the Member State thereof within three months of receipt of the notification referred to in point 12.8.2., explaining its concerns. In such a circumstance the Member State concerned shall not commence with the method of screening until it has satisfied the Commission.

12.8.4 The maximum evaluation period for each method of screening using new technologies shall be eighteen months. This evaluation period may be extended by the Commission by a maximum of a further twelve months on condition that the Member State provides adequate justification for the extension.

12.8.5 At intervals of no more than six months during the evaluation period, the appropriate authority in the Member State concerned shall provide the Commission with a progress report on the evaluation. The Commission shall inform the other Member States of the contents of the progress report. If no progress reports are provided, the Commission may request the Member State to suspend the trial.

12.8.6 If, on the basis, of a report, the Commission is not satisfied that the method of screening being trialled is providing sufficient guarantees that the overall level of aviation security is being maintained in the Community, the Commission shall inform the Member State that the trial shall be suspended until such guarantees can be given.

12.8.7 No evaluation period may be longer than thirty months.

12.9.1.1. An explosive detection dog (EDD) shall be able to detect and indicate specified and higher individual quantities of explosive material.

12.9.1.2. The detection shall be independent of the shape, position or orientation of the explosive materials.

12.9.1.3. An EDD shall give an alarm, in the form of a passive response, when it detects explosive materials set in Attachment 12-D of a separate Commission Decision.

12.9.1.4. An EDD and its handler can be used for screening if they both have been approved independently and in combination as a team.

12.9.1.5. An EDD and its handler shall be subject to initial and recurrent training to ensure that required competencies are learned and maintained and, where appropriate, new competencies are learned.

12.9.1.6. In order to be approved, an EDD team, consisting of an EDD and handler(s), shall have successfully passed a training course.

12.9.1.7. An EDD team shall be approved by or on behalf of the appropriate authority in accordance with the Attachment 12-E and 12-F of a separate Commission Decision.

12.9.1.8. After approval by the appropriate authority, an EDD team may be used for security screening by use of free running or remote explosive scent tracing method.

12.9.2.1. The performance requirements for an EDD are laid down in Attachment 12-D of a separate Commission Decision.

12.9.2.2. An EDD team used for the screening of persons, cabin baggage, items carried by persons other than passengers, vehicles, aircraft, in-flight supplies and airport supplies, and security restricted areas of an airport shall meet detection standard 1.

12.9.2.3. An EDD team used for the screening of hold baggage, air carrier mail, air carrier materials, cargo and mail shall meet detection standard 2.

12.9.2.4. An EDD team approved to detect explosive materials using the remote explosive scent tracing method may only be used in screening of cargo, but no other areas included in standard 2.

12.9.2.5. An EDD used for screening of explosive materials shall be fitted with appropriate means to allow for the unique identification of the EDD.

12.9.2.6. When performing explosive detection duties, an EDD shall always be accompanied by the handler who is approved to work with the EDD.

12.9.2.7. An EDD approved for free running method shall only have one handler. One handler may be approved for leading a maximum of two EDDs.

12.9.2.8. An EDD approved for remote explosive scent tracing method shall be led by a maximum of two handlers per EDD.

12.9.3.1. The training of an EDD team shall include theoretical, practical and on-the-job training elements.

12.9.3.2. The content of training courses shall be specified or approved by the appropriate authority.

12.9.3.3. The training shall be conducted by or on behalf of the appropriate authority using instructors qualified according to point 11.5 of the Annex to Regulation (EU) No 185/2010.

12.9.3.4. Dogs to be trained for explosive detection shall be single purpose dogs.

12.9.3.5. During training, training aids representing explosive materials shall be used.

12.9.3.6. Training shall be provided to any persons handling the training aids so as to prevent contamination.

12.9.3.7. An EDD team shall be subject to initial training which shall be based on the criteria laid down in point 12.9.3 of a separate Commission Decision.

12.9.3.8. Initial training for EDD team shall include practical training in the intended work environment.

12.9.3.9. An EDD and the handler shall be subject to recurrent training requirements, both individually and in combination as a team.

12.9.3.10. Recurrent training shall maintain the existing competencies as required by the initial training and those acquired in line with security developments.

12.9.3.11. Recurrent training for an EDD team shall be performed at intervals of at least every 6 weeks. The minimum duration of the re-current training shall be no less than 4 hours in any 6 week period.

12.9.3.12. Point 11 shall not apply in the case where an EDD is subject to recognition training of all materials listed in Attachment 12-D of a separate Commission Decision on at least a weekly basis.

12.9.3.13. The records of both initial and recurrent training shall be kept for both the EDD and its handler for at least the duration of their contract of employment and they shall be made available to the appropriate authority upon request.

12.9.3.14. When EDD is deployed in the screening duties, the EDD shall be subject to operational training to ensure that it meets the performance set in Attachment 12-D of a separate Commission Decision.

12.9.3.15. Operational training shall be done on a continuous random basis during the deployment period, and shall measure EDD’s detection performance by means of approved training aids.

12.9.4.1. The approval procedure shall ensure that the following competencies are measured:

12.9.4.2. The approval procedure shall simulate each of the work areas in which the EDD team shall work.

12.9.4.3. The EDD team shall have successfully completed training in each area for which the approval is sought.

12.9.4.4. The approval procedures shall be carried out in accordance with the Attachments 12-E and 12-F of a separate Commission Decision.

12.9.4.5. The validity of each approval period shall not be longer than 12 months.

12.9.5.1. The EDD team shall be subject to quality control measures set out in the Attachment 12-G of a separate Commission Decision.