(1)

In accordance with Article 7 of Directive 2006/42/EC machinery manufactured in conformity with a harmonised standard, the reference to which has been published in the Official Journal of the European Union, is to be presumed to comply with the essential health and safety requirements covered by such a harmonised standard.

(2)

By letter M/396 of 19 December 2006, the Commission made a request to the European Committee for Standardisation (CEN) and the European Committee for Electrotechnical Standardisation (Cenelec) (‘the request’) for the drafting, the revision and the completion of the work on harmonised standards in support of Directive 2006/42/EC to take account of changes introduced by that Directive in comparison with Directive 98/37/EC of the European Parliament and of the Council (3).

(3)

On the basis of the request, CEN drafted new harmonised standards EN 13852-3:2021 on light offshore cranes, EN 12385-5:2021 on stranded ropes for lifts, and EN 12609:2021 on safety requirements for truck mixers.

(4)

On the basis of the request, CEN and Cenelec also revised existing harmonised standards, the references of which are published in the C series of the Official Journal of the European Union by Commission Communication 2018/C 092/01 (4) to adapt them to technological progress. This resulted in the adoption of the following new harmonised standards: EN 12312-5:2021 on aircraft fuelling equipment; EN 13001-2:2021 on crane safety; EN 1501-1:2021 on rear loaded refuse collection vehicles; EN 1501-2:2021 on side loaded refuse collection vehicles; EN 1501-3:2021 on front loaded refuse collection vehicles; EN 1501-5:2021 on lifting devices for refuse collection vehicles; EN 1829-1:2021 on high pressure water jet machines; EN ISO 22868:2021 on the engineering method for noise testing portable hand-held machines with internal combustion engine; EN 303-5:2021 on heating boilers for solid fuels; EN ISO 11202:2010/A1:2021 on determining emission sound pressure levels at a work station and at other specified positions; EN ISO 19085-1:2021 on common requirements for woodworking machines; EN 1756-1:2021 on safety requirements for tail lifts; and EN IEC 62061:2021 on functional safety for safety-related control systems.

(5)

In addition, CEN and Cenelec amended harmonised standards EN 13001-3-6:2018, EN 50636-2-107:2015/A1:2018 and EN 60335-1:2012/A13:2017, the references of which have been published by Commission Implementing Decision (EU) 2019/436 (5).

(6)

The Commission together with CEN and Cenelec has assessed whether the standards drafted, revised and amended by CEN and Cenelec comply with the request.

(7)

The harmonised standards drafted, revised and amended by CEN and Cenelec on the basis of the request satisfy the safety requirements which they aim to cover and which are set out in Directive 2006/42/EC. It is therefore appropriate to publish the references of those standards in the Official Journal of the European Union, together with references of any relevant amending or correcting standards thereto.

(8)

The reference of harmonised standard EN 474-1:2006+A6:2019 was published in the Official Journal of the European Union with a restriction by Commission Implementing Decision (EU) 2021/1813 (6). It replaced the reference of harmonised standard EN 474-1:2006+A5:2018 without providing for a transitional period. In order to give manufacturers time to prepare for the application of the new standard, it is appropriate to exceptionally republish the reference to harmonised standard EN 474-1:2006+A5:2018 in the Official Journal of the European Union for a limited time period. For reasons of legal certainty, the publication of the reference to harmonised standard EN 474-1:2006+A5:2018 should cover also the period prior to the entry into force of this Decision.

(9)

The text of the restriction for harmonised standard EN 474-1:2006+A6:2019 introduced by Implementing Decision (EU) 2021/1813 is not clear, since it confuses two separate shortcomings identified with the harmonised standard.

(10)

The first shortcoming concerns the inadequate level of visibility identified with EN 474-1:2006+A6:2019 when applied in combination with EN 474-5:2006+A3:2013 requirements for hydraulic excavators. Harmonised standard EN 474-1:2006+A6:2019, similarly to harmonised standard EN 474-1:2006+A5:2018, does not ensure that the driver can operate the machinery and its tools in their foreseeable conditions of use, in complete safety for the driver and exposed persons. Therefore, the restriction provided for in harmonised standard EN 474-1:2006+A5:2018 in relation to essential health and safety requirements 1.2.2 and 3.2.1 of Annex I to Directive 2006/42/EC should be maintained for harmonised standard EN 474-1:2006+A6:2019.

(11)

The second shortcoming concerns the fact that the quick couplers mechanism used to attach hydraulic excavators and backhoe loaders to earth-moving machinery does not include an active warning system or active monitoring system for the operator when incorrectly coupling the machine with the extension. As such, harmonised standard EN 474-1:2006+A6:2019 fails to meet the essential healthy and safety requirements for safety integration and for the prevention of risks from falling objects set out in points 1.1.2 (b), 1.1.2 (c) and 1.3.3 of Annex I to Directive 2006/42/EC. Those points should be referred to in the restriction for harmonised standard EN 474-1:2006+A6:2019.

(12)

For reasons of clarity and legal certainty, the identified shortcomings should be expressed by way of two separate restrictions for harmonised standard EN 474-1:2006+A6:2019.

(13)

The reference of harmonised standard EN 60335-1:2012 was first published by Commission Communication 2012/C 159/1 (7). The reference of that standard included a reference to corrigendum EN 60335-1:2012/AC:2014 as of publication of that standard by Commission Communication 2016/C 14/1 (8). The reference of harmonised standard EN 60335-1:2012 was published in Implementing Decision (EU) 2019/436 only with reference to amendments EN 60335-1:2012/A11:2014 and EN 60335-1:2012/A13:2017. By error the reference to corrigendum EN 60335-1:2012/AC:2014 was omitted from the publication of the reference of harmonised standard EN 60335-1:2012 in Implementing Decision (EU) 2019/436. It is therefore appropriate to replace the reference of the harmonised standard EN 60335-1:2012 together with the references of amendments EN 60335-1:2012/A11:2014 and EN 60335-1:2012/A13:2017 and include the reference of corrigendum EN 60335-1:2012/AC:2014. For reasons of legal certainty, the reference of harmonised standard EN 60335-1:2012 as amended by this Decision should apply retroactively.

(14)

Implementing Decision (EU) 2019/436 provides in Annex I the references of harmonised standards conferring a presumption of conformity with Directive 2006/42/EC and provides in Annex II the references of harmonised standards conferring a presumption of conformity with restrictions. In order to ensure that the references of harmonised standards drafted in support of Directive 2006/42/EC are listed in one act, the references of the standards that are replaced, revised or amended by CEN and Cenelec should be included in Implementing Decision (EU) 2019/436.

(15)

Annex III to Implementing Decision (EU) 2019/436 lists the references of harmonised standards in support of Directive 2006/42/EC that are withdrawn from the C series of the Official Journal of the European Union as from the dates set out in that Annex.

(16)

As a result of the work by CEN and Cenelec on the basis of the request, the following harmonised standards published in the C series of the Official Journal of the European Union have been replaced, revised or amended: EN 12312-5:2005+A1:2009; EN 13001-2:2014; EN 1501-1:2011+A1:2015; EN 1501-2:2005+A1:2009; EN 1501-3:2008; EN 1501-5:2011; EN 1829-1:2010; EN ISO 22868:2011; EN 303-5:2012; EN ISO 11202:2010; EN ISO 19085-1:2017; EN 1756-1:2001+A1:2008; and EN 62061:2005/A2:2015. It is therefore necessary to withdraw the references of those standards from the Official Journal of the European Union by including those references in Annex III to Implementing Decision (EU) 2019/436.

(17)

It is also necessary to withdraw the references of harmonised standards EN 13001-3-6:2018, EN 50636-2-107:2015/A2:2020; and EN 60335-1:2012/A13:2017 published by Implementing Decision (EU) 2019/436, given that those standard have been amended. It is therefore appropriate to delete those reference from Annex I to that Implementing Decision.

(18)

In order to give manufacturers sufficient time to prepare for application of the new, revised or amended standards, it is necessary to defer the withdrawal of the references of the following harmonised standards: EN 12312-5:2005+A1:2009; EN 13001-2:2014; EN 1501-1:2011+A1:2015; EN 1501-2:2005+A1:2009; EN 1501-3:2008; EN 1501-5:2011; EN 1829-1:2010; EN ISO 22868:2011; EN 303-5:2012; EN ISO 11202:2010; EN ISO 19085-1:2017; EN 1756-1:2001+A1:2008; EN 62061:2005/A2:2015; EN 13001-3-6:2018, EN 50636-2-107:2015/A2:2020; and EN 60335-1:2012/A13:2017.

(19)

Implementing Decision (EU) 2019/436 should therefore be amended accordingly.

(20)

Compliance with a harmonised standard confers a presumption of conformity with the corresponding essential requirements set out in Union harmonisation legislation from the date of publication of the reference of such standard in the Official Journal of the European Union. This Decision should therefore enter into force on the date of its publication,

(1)

in Article 1, the following paragraph is added:

‘The reference of harmonised standard EN 474-1:2006+A5:2018 for Earth-moving machinery drafted in support of Directive 2006/42/EC, listed in Annex IIA to this Decision, is hereby published with restriction in the Official Journal of the European Union. That reference shall be deemed to have been published in the Official Journal of the European Union for the period set out in that Annex.’;

(2)

Annex I is amended in accordance with Annex I to this Decision;

(3)

Annex II is amended in accordance with Annex II to this Decision;

(4)

Annex IIA, as set out in Annex III to this Decision, is inserted;

(5)

Annex III is amended in accordance with Annex IV to this Decision.