2008R1099 — EN — 21.05.2014 — 003.001

---

This document is meant purely as a documentation tool and the institutions do not assume any liability for its contents

►B	REGULATION (EC) No 1099/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 22 October 2008 on energy statistics (Text with EEA relevance) (OJ L 304, 14.11.2008, p.1)

Amended by:

		Official Journal
		No	page	date
M1	Commission Regulation (EU) No 844/2010 of 20 September 2010	L 258	1	30.9.2010
►M2	Commission Regulation (EU) No 147/2013 of 13 February 2013	L 50	1	22.2.2013
►M3	Commission Regulation (EU) No 431/2014 of 24 April 2014	L 131	1	1.5.2014

---

▼B

REGULATION (EC) No 1099/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

of 22 October 2008

on energy statistics

(Text with EEA relevance)

Article 1

Subject matter and scope

1.  This Regulation establishes a common framework for the production, transmission, evaluation and dissemination of comparable energy statistics in the Community.

2.  This Regulation shall apply to statistical data concerning energy products and their aggregates in the Community.

Article 2

Definitions

For the purpose of this Regulation, the following definitions shall apply:

Article 3

Data sources

1.  While applying the principles of maintaining a reduced burden on respondents and of administrative simplification, Member States shall compile data concerning energy products and their aggregates in the Community from the following sources:

2.  Member States shall lay down the detailed rules concerning the reporting of the data needed for the national statistics as specified in Article 4 by undertakings and other sources.

3.  The list of data sources may be modified in accordance with the regulatory procedure with scrutiny referred to in Article 11(2).

Article 4

Aggregates, energy products and the transmission frequency of national statistics

1.  The national statistics to be reported shall be as set out in the Annexes. They shall be transmitted with the following frequencies:

2.  Applicable clarifications or definitions of the technical terms used are provided in the individual Annexes and also in Annex A (Clarifications of terminology).

3.  The data to be forwarded and the applicable clarifications or definitions may be modified in accordance with the regulatory procedure with scrutiny referred to in Article 11(2).

Article 5

Transmission and dissemination

1.  Member States shall transmit to the Commission (Eurostat) the national statistics referred to in Article 4.

2.  The arrangements for their transmission, including the applicable time limits, derogations and exemptions therefrom, shall be as set out in the Annexes.

3.  The arrangements for the transmission of the national statistics may be modified in accordance with the regulatory procedure with scrutiny referred in Article 11(2).

4.  At the duly justified request of a Member State, additional exemptions or derogations may be granted by the Commission in accordance with the regulatory procedure referred to in Article 11(3), for those parts of the national statistics for which the collection would lead to an excessive burden on respondents.

5.  The Commission (Eurostat) shall disseminate yearly energy statistics by 31 January of the second year following the reported period.

Article 6

Quality assessment and reports

1.  Member States shall ensure the quality of the data transmitted.

2.  Every reasonable effort shall be undertaken to ensure coherence between energy data declared in accordance with Annex B and data declared in accordance with Commission Decision 2005/166/EC of 10 February 2005 laying down the rules for implementing Decision No 280/2004/EC of the European Parliament and of the Council concerning a mechanism for monitoring Community greenhouse gas emissions and for implementing the Kyoto Protocol ( 12 ).

3.  For the purposes of this Regulation, the following quality assessment dimensions shall apply to the data to be transmitted:

4.  Every five years, Member States shall provide the Commission (Eurostat) with a report on the quality of the data transmitted as well as on any methodological changes that have been made.

5.  Within six months of receipt of a request from the Commission (Eurostat), and in order to allow it to assess the quality of the data transmitted, Member States shall send to the Commission (Eurostat) a report containing any relevant information concerning the implementation of this Regulation.

Article 7

Time reference and frequency

Member States shall compile all data specified in this Regulation from the beginning of the calendar year following the adoption of this Regulation, and shall transmit them from then onwards with the frequencies laid down in Article 4(1).

Article 8

Annual nuclear statistics

The Commission (Eurostat) shall, in cooperation with the nuclear energy sector in the EU, define a set of annual nuclear statistics which shall be reported and disseminated from 2009 onwards, that year being the first reported period, without prejudice to confidentiality, where it is necessary, and avoiding any duplication of data collection, while at the same time keeping production costs low and the reporting burden reasonable.

The set of annual nuclear statistics shall be established and may be modified in accordance with the regulatory procedure with scrutiny referred to in Article 11(2).

Article 9

Renewable energy statistics and final energy consumption statistics

1.  With a view to improving the quality of renewable energy and final energy consumption statistics, the Commission (Eurostat), in collaboration with the Member States, shall make sure that these statistics are comparable, transparent, detailed and flexible by:

2.  The set of renewable energy statistics may be modified in accordance with the regulatory procedure with scrutiny referred to in Article 11(2).

3.  The set of final energy consumption statistics shall be established and may be modified in accordance with the regulatory procedure with scrutiny referred to in Article 11(2).

Article 10

Implementing measures

1.  The following measures necessary for implementation of this Regulation, designed to amend non-essential elements of this Regulation, inter alia, by supplementing it, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 11(2):

2.  Additional exemptions or derogations (Article 5(4)) shall be granted in accordance with the regulatory procedure referred to in Article 11(3).

3.  Consideration is to be given to the principle that additional costs and the reporting burden remain within reasonable limits.

Article 11

Committee

1.  The Commission shall be assisted by the Statistical Programme Committee.

2.  Where reference is made to this paragraph, Article 5a(1) to (4) and Article 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.

3.  Where reference is made to this paragraph Articles 5 and 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.

The period provided for in Article 5(6) of Decision 1999/468/EC shall be three months.

Article 12

Entry into force

This Regulation shall enter into force on the 20th day following its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

▼M3

---

ANNEX A

CLARIFICATIONS OF TERMINOLOGY

This Annex supplies explanations or definitions of terms that are used in the other Annexes.

1.   GEOGRAPHICAL NOTES

For statistical reporting purposes only, the following geographical definitions apply:

2.   AGGREGATES

Producers are classified according to the purpose of production:

—	Main activity producer : enterprises, both privately or publicly owned, which generate electricity and/or heat for sale to third parties, as their principal activity,

—	Autoproducers : enterprises, both privately or publicly owned, which generate electricity and/or heat wholly or partly for their own use as an activity which supports their primary activity.

Note: the Commission may further clarify terminology by adding relevant NACE references in accordance with the regulatory procedure with scrutiny referred to in Article 11(2) after a revision of the NACE classification has entered into force.

2.1.    Supply and Transformation Sectors

Quantities of fuels extracted or produced, calculated after any operation for removal of inert matter. Production includes the quantities consumed by the producer in the production process (e.g. for heating or operation of equipment and auxiliaries) as well as supplies to other producers of energy for transformation or other uses.

Indigenous means: production from resources within the concerned state.

For geographical definitions see ‘Geographical Notes’ section.

Unless specified differently, ‘imports’ refer to ultimate origin (the country in which the energy product was produced) for use in the country and ‘exports’ to the ultimate country of consumption of the produced energy product.

Amounts are considered as imported or exported when they have crossed the political boundaries of the country, whether customs clearance has taken place or not.

Where no origin or destination can be reported ‘Other’ may be used.

Statistical differences may arise if only total import and export are available on the above basis, while the geographical breakdown is based on a different survey, source or concept. In this case, differences shall be included under ‘Other’.

Quantities of fuels delivered to ships of all flags that are engaged in international navigation. The international navigation may take place at sea, on inland lakes and waterways, and in coastal waters. Excluded is:

The difference between the opening stock level and closing stock level for stocks held on national territory.

Calculated value, defined as:

Indigenous production + From other sources + Imports – Exports – International marine bunkers + Stock changes

The quantity actually recorded in surveys of end-use sectors.

Calculated value, defined as:

Calculated gross consumption – observed gross consumption.

Includes changes in stocks at final consumers when this cannot be specified as part of the ‘Stock changes’.

Reasons for any major differences should be stated.

Fuel quantities used to produce electricity.

Fuels used by plants containing at least one CHP unit are to be reported under Main Activity Producer CHP Plants.

Quantities of fuels used to produce electricity and heat.

Quantities of fuels used to produce heat.

Quantities of fuels used to produce electricity.

Fuels used by plants containing at least one CHP unit are to be reported under Autoproducer CHP Plants.

Quantities of fuels that correspond to the quantity of electricity produced and heat sold.

Quantities of fuels that correspond to the quantity of heat sold.

Quantities used to produce fuels.

Quantities used for heating and operation of equipment should not be declared here, but declared as consumption in the Energy sector.

Quantities used in coke ovens.

Quantities used for heating and operation of equipment should not be declared here, but declared as consumption in the Energy sector.

Quantities of lignite used to produce brown coal briquettes (BKB) or of peat to produce peat briquettes (PB).

Quantities used for heating and operation of equipment should not be declared here, but declared as consumption in the Energy sector.

Quantities used to produce gas in gas works and coal gasification plants.

Quantities used as a fuel for heating and operation of equipment should not be included here, but declared as consumption in the Energy sector.

Quantities of coking coal and/or bituminous coal (generally referred to as PCI) and coke oven coke transformed in blast furnaces.

Quantities used as a fuel for heating and operation of blast furnaces (e.g.: blast furnaces gas) should not be included here, but declared as consumption in the Energy sector.

Quantities of fuel used to produce synthetic oil.

Quantities used to produce petroleum products.

Quantities used as a fuel for heating and operation of equipment should not be declared here, but declared as consumption in the Energy sector.

Quantities used for transformation activities not included elsewhere. If used, what is included under this heading should be explained in the report.

2.2.    Energy sector and final consumption

Quantities consumed by the energy industry to support the extraction (mining, oil and gas production) or plant operations of transformation activities. This corresponds to NACE Divisions 05, 06, 08.92, 07.21, 09.1, 19 and 35.

Excludes quantities of fuels transformed into another energy form (which should be reported under the Transformation sector) or used in support of the operation of oil, gas and coal slurry pipelines (which should be reported in the Transport Sector).

Includes the manufacture of chemical materials for atomic fission and fusion and the products of these processes.

Quantities consumed as energy at electricity plants, combined heat and power plants (CHP) and heat plants.

Quantities consumed as energy to support the extraction and preparation of coal within the coal mining industry.

Coal burned in pithead power stations should be reported in the Transformation Sector.

Quantities consumed as energy at patent fuel plants.

Quantities consumed as energy at coking plants.

Quantities used as energy in BKP/PB plants.

Quantities consumed as energy at gas works and coal gasification plants.

Quantities consumed as energy at blast furnaces.

Quantities consumed as energy at coal liquefaction plants.

Quantities consumed as energy at petroleum refineries.

Quantities consumed as fuel in the oil and gas extraction process and in natural gas processing plants.

Excludes pipeline losses (to be reported as distribution losses) and energy quantities used to operate pipelines (to be reported in the Transport sector).

Defined (calculated) as:

= Total non-energy use + Final Energy Consumption (Industry + Transport + Other sectors)

It excludes deliveries for transformation, use by the energy producing industries, and distribution losses.

Energy products used as raw materials in the different sectors; that is, not consumed as a fuel or transformed into another fuel.

2.3.    Energy end-use Specification

Total energy consumption in industry, transport and other sectors.

This refers to fuel quantities consumed by the industrial undertaking in support of its primary activities.

For heat only or CHP plants, only quantities of fuels consumed for the production of heat used by the plant itself are applicable. Quantities of fuels consumed for the production of heat that is sold, and for the production of electricity, should be reported under the appropriate Transformation sector.

Iron and Steel: NACE Divisions 24.1, 24.2, 24.3, 24.51 and 24.52.

Chemical and petrochemical industries; NACE Divisions 20 and 21.

Non-ferrous metals industries; NACE Divisions 24.4, 24.53 and 24.54.

Glass, ceramic, cement and other building materials industries; NACE Division 23.

Industries related to the equipment used for transport; NACE Divisions 29 and 30.

Fabricated metal products, machinery and equipment other than transport equipment; NACE Divisions 25, 26, 27 and 28.

NACE Divisions 07 (except 07.21), 08 (except 08.92) and 09.9; it excludes energy producing industries.

Food, Beverages and Tobacco: NACE Divisions 10, 11 and 12.

Includes production of recorded media; NACE Divisions 17 and 18.

Wood and Wood Products (other than pulp and paper): NACE Division 16.

Construction: NACE Division 41, 42 and 43.

Textile and Leather; NACE Divisions 13, 14 and 15.

Consumption in sectors which is not covered above.

Energy used in all transport activities irrespective of the economic sector in which the activity occurs; NACE Divisions 49, 50 and 51.

All consumption for use in rail traffic, including industrial railways; NACE Divisions 49.1 and 49.2.

Quantities delivered to vessels of all flags not engaged in international navigation (see International marine bunkers). The domestic/international split should be determined on the basis of port of departure and port of arrival and not by the flag or nationality of the ship. NACE Division 50.

Quantities used in road vehicles.

Includes fuel used by agricultural vehicles on highways and lubricants for use in road vehicles.

Excludes energy used in stationary engines (see Other sector), for non-highway use in tractors (see Agriculture), military use in road vehicles (see Other sector – Not elsewhere specified), bitumen used in road surfacing and energy used in engines at construction sites (see Industry sub-sector Construction). NACE Divisions 49.3 and 49.4.

Quantities used as energy in the support and operation of pipelines transporting gases, liquids, slurries and other commodities; NACE Division 49.5.

Includes energy used for pump stations and maintenance of the pipeline.

Excludes energy used for the pipeline distribution of natural or manufactured gas, hot water or steam from the distributor to final users (to be reported in the energy sector), energy used for the final distribution of water to household, industrial, commercial and other users (to be included in Commercial and Public Services) and losses occurring during this transport between distributor and final users (to be reported as distribution losses).

Quantities of aviation fuels delivered to aircraft for international aviation. The domestic/international split should be determined on the basis of departure and landing locations and not by the nationality of the airline. Part of NACE Division 51.

Excludes fuels used by airlines for their road vehicles (to be reported in the transport sector – Not elsewhere specified) and military use of aviation fuels (to be reported in the Other sectors – Not elsewhere specified).

Quantities of aviation fuels delivered to aircraft for domestic aviation – commercial, private, agricultural, etc. Part of NACE Division 51.

Includes fuel used for purposes other than flying, e.g. bench testing of engines. The domestic/international split should be determined on the basis of departure and landing locations and not by the nationality of the airline.

Excludes fuels used by airlines for their road vehicles (to be reported in the transport sector – Not elsewhere specified) and military use of aviation fuels (to be reported in the Other sector – Not elsewhere specified).

Quantities used for transport activities not included elsewhere.

Includes fuels used by airlines for their road vehicles and fuels used in ports for ships’ unloaders, various types of cranes.

To be declared is what is included under this heading.

Sectors not specifically mentioned or not belonging to energy, industry or transport.

Fuels consumed by business and offices in the public and private sectors.

NACE Divisions 33, 36, 37, 38, 39, 45, 46, 47, 52, 53, 55, 56, 58, 59, 60, 61, 62, 63, 64, 65, 66, 68, 69, 70, 71, 72, 73, 74, 75, 77, 78, 79, 80, 81, 82, 84, 85, 86, 87, 88, 90, 91, 92, 93, 94, 95, 96 and 99.

To be declared are fuels consumed by all households including ‘households with employed persons’. NACE Divisions 97 and 98.

The following specific definitions apply for this sector:

Household means a person living alone or a group of people who live together in the same private dwelling and sharing expenditures including the joint provision of the essentials of living. The household sector, also known as the residential (or domestic) sector is therefore, a collective pool of all households in a country.

Collective residences which can be permanent (e.g. prisons) or temporary (e.g. hospitals) should be excluded as these are covered in consumption in the service sector. Energy used in all transport activities should be reported in the transport sector and not in the household sector.

Energy consumption associated with significant economic activities of households should also be excluded from the total household energy consumption. These activities include agricultural economic activities on small farms and other economic activities carried out in a household’s residence and should be reported in the corresponding sector.

This energy service refers to the use of energy to provide heat in an interior area of a dwelling.

This energy service is referred to the use of energy for cooling in a dwelling by a refrigeration system and/or unit.

Fans, blowers and other appliances not connected to a refrigeration unit are excluded from this section, but should be covered in the lighting and electrical appliances section.

This energy service is referred to the use of energy to heat water for hot running water, bathing, cleaning and other non-cooking applications.

Swimming pool heating is excluded, but should be covered in the other end uses section.

This energy service is referred to the use of energy to prepare meals.

Appliances for auxiliary cooking (microwave ovens, kettles, coffee makers, etc.) are excluded; they should be covered in the the lighting and electrical appliances section

Use of electricity for lighting and any other electrical appliances in a dwelling not considered within other end uses.

Any other energy consumption in households such as use of energy for the outdoor and any other activities not included into the five energy end-uses mentioned above (e.g. lawn mowers, swimming pool heating, outdoor heaters, outdoor barbecues, saunas etc.).

Fuels consumed by users classified as agriculture, hunting and forestry; NACE Divisions 01 and 02.

Fuels delivered for inland, coastal and deep-sea fishing. Fishing should cover fuels delivered to ships of all flags that have refuelled in the country (include international fishing) and energy used in the fishing industry. NACE Division 03.

These are activities not included elsewhere. This category includes military fuel use for all mobile and stationary consumption (e.g. ships, aircraft, road and energy used in living quarters), regardless of whether the fuel delivered is for the military of that country or for the military of another country. If used, what is included under this heading should be explained in the report.

3.   OTHER TERMS

The meaning of the following abbreviations applies:

—	TML : tetramethyl lead,

—	TEL : tetraethyl lead,

—	SBP : special boiling point,

—	LPG : liquified petroleum gas,

—	NGL : natural gas liquids,

—	LNG : liquefied natural gas,

—	CNG : compressed natural gas.

---

ANNEX B

ANNUAL ENERGY STATISTICS

This Annex describes the scope, units, reported period, frequency, deadline and transmission modalities for the annual collection of energy statistics.

Annex A applies for explanations of terms for which a specific explanation is not supplied in this Annex.

1.   SOLID FOSSIL FUELS AND MANUFACTURED GASES

1.1.    Applicable energy products

Unless otherwise specified this data collection applies to all of the following energy products:

1.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

Annex A applies for explanations of terms for which a specific explanation is not supplied in this annex.

1.2.1.    Supply and Transformation Sectors

1.   Production

1.1.	Of which: underground Applicable only for anthracite, coking coal, other bituminous coal, subbituminous coal and lignite.

1.2.	Of which: surface Applicable only for anthracite, coking coal, other bituminous coal, subbituminous coal and lignite.

2.   From Other Sources

This consists of two components:

2.1.	Of which: from oil products Not applicable for anthracite, coking coal, other bituminous coal, subbituminous coal, lignite, peat, peat products and oil shale and oil sands. E.g.: petroleum coke addition to coking coal for coke ovens

2.2.	Of which: from natural gas Not applicable for anthracite, coking coal, other bituminous coal, subbituminous coal, lignite, peat, peat products and oil shale and oil sands. E.g.: natural gas addition to gas works gas for direct final consumption

2.3.	Of which: from renewables Not applicable for anthracite, coking coal, other bituminous coal, subbituminous coal, lignite, peat, peat products and oil shale and oil sands. E.g.: industrial waste as binding agent in the manufacturing of patent fuel

3.   Imports

4.   Exports

5.   International Marine Bunkers

6.   Stock changes

A stock build is shown as a negative number and a stock draw is shown as a positive number.

7.   Gross consumption

8.   Statistical differences

9.   Total transformation Sector

Quantities of fuels used for the primary or secondary conversion of energy (e.g. coal to electricity, coke oven gas to electricity) or used for the transformation to derived energy products (e.g.: coking coal to coke).

9.1.	Of which: Main Activity Producer Electricity Plants

9.2.	Of which: Main Activity Producer CHP Plants

9.3.	Of which: Main Activity Producer Heat Plants

9.4.	Of which: Autoproducer Electricity plants

9.5.	Of which: Autoproducer CHP plants

9.6.	Of which: Autoproducer Heat plants

9.7.	Of which: Patent Fuel Plants

9.8.	Of which: Coke Ovens

9.9.	Of which: BKB/PB Plants

9.10.

Of which: Gas Works

9.11.

Of which: Blast Furnaces Quantities of coking coal and/or bituminous coal (generally referred to as PCI) and coke oven coke transformed in blast furnaces. Amounts used as a fuel for heating and operation of blast furnaces (e.g.: blast furnaces gas) should not be included in the transformation sector, but reported as consumption in the energy sector.

9.12.

Of which: Coal Liquefaction Shale oil and other products derived from liquefaction should be reported as per Chapter 4 of this annex.

9.13.

Of which: For Blended Natural Gas Quantities of coal gases blended with natural gas.

9.14.

Of which: Not Elsewhere Specified – Transformation

1.2.2.    Energy Sector

1.   Total Energy Sector

1.1.	Of which: Electricity, CHP and Heat plants

1.2.	Of which: Coal Mines

1.3.	Of which: Patent Fuel Plants

1.4.	Of which: Coke Ovens

1.5.	Of which: BKB/PB Plants

1.6.	Of which: Gas Works

1.7.	Of which: Blast Furnaces

1.8.	Of which: Petroleum Refineries

1.9.	Of which: Coal Liquefaction

1.10.

Of which: Not Elsewhere Specified – Energy

2.   Distribution losses

Losses occurred due to transport and distribution, as well as flaring of manufactured gases.

3.   Total Final Consumption

4.   Total Non-energy use

4.1.

Of which: Industry, Transformation and Energy Sectors Non-energy use in all industry, transformation and energy sub-sectors, e.g. coal used to make methanol or ammonia. 4.1.1. From 4.1, of which: in the petrochemical sector Non-energy use e.g. coal use as feedstocks to produce fertiliser and as feedstocks for other petrochemical products.

4.2.	Of which: Transport Sector Non-energy use in all Transport sub-sectors.

4.3.	Of which: Other Sectors Non-energy use in Commercial and Public Services, Residential, Agriculture and Not Elsewhere Specified Other.

1.2.3.    Energy end-use specification

1.   Final Energy Consumption

2.   Industry Sector

2.1.	Of which: Iron and Steel

2.2.	Of which: Chemical and Petrochemical

2.3.	Of which: Non-Ferrous Metals

2.4.	Of which: Non-Metallic Minerals

2.5.	Of which: Transport Equipment

2.6.	Of which: Machinery

2.7.	Of which: Mining and Quarrying

2.8.	Of which: Food, Beverages and Tobacco

2.9.	Of which: Pulp, Paper and printing

2.10.

Of which: Wood and Wood Products

2.11.

Of which: Construction

2.12.

Of which: Textile and Leather

2.13.

Of which: Not Elsewhere Specified – Industry

3.   Transport Sector

3.1.	Of which: Rail

3.2.	Of which: Domestic Navigation

3.3.	Of which: Not Elsewhere Specified – Transport

4.   Other Sectors

4.1.	Of which: Commercial and Public Services

4.2.	Of which: Residential 4.2.1. Residential, of which: Space heating 4.2.2. Residential, of which: Space cooling 4.2.3. Residential, of which: Water heating 4.2.4. Residential, of which: Cooking 4.2.5. Residential, of which: Other end uses

4.3.	Of which: Agriculture/Forestry

4.4.	Of which: Fishing

4.5.	Of which: Not Elsewhere Specified – Other

1.2.4.    Imports and exports

Imports by country of origin, and exports by country of destination.

Applicable to anthracite, coking coal, other bituminous coal, sub-bituminous coal, lignite, patent fuel, coke oven coke, coal tar, bkb, peat, peat products and oil shale and oil sands.

1.3.    Calorific values

Applicable for anthracite, coking coal, other bituminous coal, sub-bituminous coal, lignite, patent fuel, coke oven coke, gas coke, coal tar, bkb, peat, peat products, oil shale and oil sands.

Both gross and net calorific values are to be declared for the following main aggregates:

1.   Production

2.   Imports

3.   Exports

4.   Used in coke ovens

5.   Used in blast furnaces

6.   Used in Main Activity Producer Electricity, CHP and Heat Plants

7.   Used in Industry

8.   For Other Uses

1.4.    Units of measurement

1.5.    Derogations and exemptions

Not applicable.

2.   NATURAL GAS

2.1.    Applicable energy products

This data collection applies to natural gas, which comprises gases occurring in underground deposits, whether liquefied or gaseous, consisting mainly of methane.

It includes both ‘non-associated’ gas originating from fields producing hydrocarbons only in gaseous form, and ‘associated’ gas produced in association with crude oil as well as methane recovered from coal mines (colliery gas) or from coal seams (coal seam gas).

It does not include gases created by anaerobic digestion of biomass (e.g. municipal or sewage gas) nor gas works gas.

2.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

2.2.1.    Supply and Transformation Sectors

To be declared are quantities expressed in both volume and energy units, and including the gross and net calorific values, for the following aggregates:

1.   Indigenous Production

All dry marketable production within national boundaries, including offshore production. Production is measured after purification and extraction of NGLs and sulphur.

Excludes extraction losses and quantities reinjected, vented or flared.

Includes quantities used within the natural gas industry; in gas extraction, pipeline systems and processing plants.

1.1.	Of which: Associated Gas Natural gas produced in association with crude oil.

1.2.	Of which: Non-Associated Gas Natural gas originating from fields producing hydrocarbons only in gaseous form.

1.3.	Of which: Colliery Gas Methane produced at coal mines or from coal seams, piped to the surface and consumed at collieries or transmitted by pipeline to consumers.

2.   From Other Sources

Fuel which are blended with natural gas, and consumed as a blend.

2.1.	Of which: from oil products LPG for upgrading the quality e.g. heat content

2.2.	Of which: from coal manufactured gas for blending with natural gas

2.3.	Of which: from renewables biogas for blending with natural gas

3.   Imports

4.   Exports

5.   International Marine Bunkers

6.   Stock changes

A stock build is shown as a negative number and a stock draw is shown as a positive number.

7.   Gross consumption

8.   Statistical differences

The requirement of declaring calorific values is not applicable here.

9.   Recoverable gas: opening and closing stocks

Quantities of gas available for delivery during any input-output cycle. This refers to recoverable natural gas stored in special storage facilities (depleted gas and/or oil field, aquifer, salt cavity, mixed caverns, or other) as well as liquefied natural gas storage. Cushion gas should be excluded.

The requirement of declaring calorific values is not applicable here.

10.   Gas Vented

The volume of gas released into the air on the production site or at the gas processing plant.

The requirement of declaring calorific values is not applicable here.

11.   Gas Flared

The volume of gas burned in flares on the production site or at the gas processing plant.

The requirement of declaring calorific values is not applicable here.

12.   Total transformation Sector

Quantities of fuels used for the primary or secondary conversion of energy (e.g. natural gas to electricity) or used for the transformation to derived energy products (e.g. natural gas to methanol).

12.1.

Of which: Main Activity Producer Electricity Plants

12.2.

Of which: Autoproducer Electricity plants

12.3.

Of which: Main Activity Producer CHP Plants

12.4.

Of which: Autoproducer CHP plants

12.5.

Of which: Main Activity Producer Heat Plants

12.6.

Of which: Autoproducer Heat plants

12.7.

Of which: Gas Works

12.8.

Of which: Coke Ovens

12.9.

Of which: Blast Furnaces

12.10.

Of which: Gas to liquids Quantities of natural gas used as feedstock for the conversion to liquids e.g. the quantities of fuel entering the methanol production process for transformation into methanol.

12.11.

Of which: Non specified – Transformation

2.2.2.    Energy Sector

1.   Total Energy Sector

1.1.	Of which: Coal Mines

1.2.	Of which: Oil and Gas extraction

1.3.	Of which: Inputs to oil refineries

1.4.	Of which: Coke Ovens

1.5.	Of which: Blast Furnaces

1.6.	Of which: Gas Works

1.7.	Of which: Electricity, CHP and Heat Plants

1.8.	Of which: Liquefaction (LNG) or Gasification

1.9.	Of which: Gas to Liquids

1.10.

Of which: Not Elsewhere Specified – Energy

2.   Losses of distribution and transport

2.2.3.    Energy end-use specification

Consumption of natural gas needs to be reported for both energy use and (wherever applicable) non-energy use separately, for all of the following aggregates:

1.   Total Final Consumption

Final energy consumption and non-energy use to be declared separately under this heading.

2.   Transport Sector

2.1.	Of which: Transport by road Includes both CNG and biogas. 2.1.1. Of which: Biogas fraction in Transport by Road

2.2.	Of which: Pipeline transport

2.3.	Of which: Not Elsewhere Specified – Transport

3.   Industry Sector

3.1.	Of which: Iron and Steel

3.2.	Of which: Chemical and Petrochemical

3.3.	Of which: Non-Ferrous Metals

3.4.	Of which: Non-Metallic Minerals

3.5.	Of which: Transport Equipment

3.6.	Of which: Machinery

3.7.	Of which: Mining and Quarrying

3.8.	Of which: Food, Beverages and Tobacco

3.9.	Of which: Pulp, Paper and printing

3.10.

Of which: Wood and Wood Products

3.11.

Of which: Construction

3.12.

Of which: Textile and Leather

3.13.

Of which: Not Elsewhere Specified – Industry

4.   Other Sectors

4.1.	Of which: Commercial and Public Services

4.2.	Of which: Residential 4.2.1. Residential, of which: Space heating 4.2.2. Residential, of which: Space cooling 4.2.3. Residential, of which: Water heating 4.2.4. Residential, of which: Cooking 4.2.5. Residential, of which: Other end uses

4.3.	Of which: Agriculture/Forestry

4.4.	Of which: Fishing

4.5.	Of which: Not Elsewhere Specified – Other

2.2.4.    Imports and exports

To be declared are both the quantities of the total natural gas and of the LNG part of it, per country of origin for imports and per country of destination for exports.

2.2.5.    Gas Storage Capacities

1.   Name

Name of the site of the storage facility.

2.   Type

Type of storage, such as depleted gas field, salt cavern, etc.

3.   Working Capacity

Total gas storage capacity, minus the cushion gas. The cushion gas is the total volume of gas required as a permanent inventory to maintain adequate underground storage reservoir pressures and deliverability rates throughout the output cycle.

4.   Peak Output

Maximum rate at which gas can be withdrawn from the concerned storage; this corresponds to the maximum withdrawal capacity.

2.3.    Units of measurement

2.4.    Derogations and exemptions

Not applicable.

3.   ELECTRICITY AND HEAT

3.1.    Applicable energy products

This chapter covers heat and electricity.

3.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

Annex A applies for explanations of terms for which a specific explanation is not supplied in this chapter. The definitions and units mentioned in Chapters 1, 2, 4 and 5 apply to energy products belonging to solid fuels and manufactured gases, natural gas, oil and petroleum products, and renewable energy and energy from waste.

3.2.1.    Supply and Transformation Sectors

The following specific definitions apply to aggregates for electricity and heat in this chapter:

—	Gross Electricity Production : the sum of the electrical energy production by all the generating sets concerned (including pumped storage) measured at the output terminals of the main generators.

—

Gross Heat Production : the total heat produced by the installation and includes the heat used by the installation’s auxiliaries which use a hot fluid (space heating, liquid fuel heating etc.) and losses in the installation/network heat exchanges, as well as heat from chemical processes used as a primary energy form.

—	Net Electricity Production : the gross electricity production less the electrical energy absorbed by the generating auxiliaries and the losses in the main generator transformers.

—	Net Heat Production : the heat supplied to the distribution system as determined from measurements of the outgoing and return flows.

The aggregates mentioned in the next table must be declared separately for main activity producer plants and for autoproducer plants. Within these two types of plants, both gross and net electricity and heat production must be declared for electricity only, for CHP and for heat only plants separately wherever applicable, for the following aggregates:

1.   Total production

1.1.	Of which: Nuclear

1.2.	Of which: Hydro 1.2.1. Of which: part of hydro produced from pumped storage

1.3.	Of which: Geothermal

1.4.	Of which: Solar

1.5.	Of which: Tide, wave, ocean

1.6.	Of which: Wind

1.7.	Of which: Combustible fuels Fuels capable of igniting or burning, i.e. reacting with oxygen to produce a significant rise in temperature and combusted directly for the production of electricity and/or heat.

1.8.	Of which: Heat Pumps Heat output from heat pumps only where the heat is sold to third parties (i.e. in cases where production occurs in the Transformation Sector).

1.9.	Of which: Electric Boilers Quantities of heat from electric boilers where the output is sold to third parties.

1.10.

Of which: Heat from Chemical Processes Heat originating from processes without input energy, such as a chemical reaction. Excludes waste heat originating from energy driven processes, which should be reported as heat produced from the corresponding fuel.

1.11.

Of which: Other Sources (please specify)

The aggregates mentioned in the next table must be declared as totals, for electricity and heat separately, wherever applicable. For the three first aggregates in the next table, quantities should be calculated from and be compatible with the values declared according to the previous table.

1.   Total Gross Production

2.   Own Use by Plant

3.   Total Net Production

4.   Imports

See also explanation under 5 ‘Exports’.

5.   Exports

Amounts of electricity are considered as imported or exported when they have crossed the political boundaries of the country, whether customs clearance has taken place or not. If electricity is transited through a country, the amount should be reported as both an import and an export.

6.   Used for Heat Pumps

7.   Used for Electric Powered Steam Boilers

8.   Used for Pumped Storage

9.   Used for Electricity Production

10.   Energy Supplied

For electricity: the sum of the net electrical energy production supplied by all power stations within the country, reduced by the amount used simultaneously for heat pumps, electrically powered steam boilers, pumping and reduced or increased by exports to or imports from abroad.

For heat: the sum of the net heat production for sale by all plants within a country, reduced by heat used for electricity production and reduced or increased by exports or imports from abroad.

11.   Transmission and Distribution Losses

All losses due to transport and distribution of electrical energy and heat.

For electricity, includes losses in transformers which are not considered as integral parts of the power plants.

12.   Total Consumption (calculated)

13.   Statistical Difference

14.   Total Consumption (observed)

The electricity produced, the heat sold and the fuel quantities used including their corresponding total energy from the combustibles listed in the next table must be declared separately for main activity producer plants and for autoproducer plants. Within these two types of plants, this electricity and heat production must be declared for electricity (only) plants, for CHP and for heat (only) plants separately wherever applicable:

1.   Solid fuels and manufactured gases:

1.1.   Anthracite

1.2.   Coking Coal

1.3.   Other Bituminous Coal

1.4.   Sub-Bituminous Coal

1.5.   Lignite

1.6.   Peat

1.7.   Patent Fuel

1.8.   Coke Oven Coke

1.9.   Gas Coke

1.10.   Coal Tar

1.11.   BKB (Brown Coal Briquettes)

1.12.   Gas Works Gas

1.13.   Coke Oven Gas

1.14.   Blast Furnace Gas

1.15.   Other recovered Gases

1.16.   Peat products

1.17.   Oil shale and oil sands

2.   Oil and Petroleum Products:

2.1.   Crude Oil

2.2.   NGL

2.3.   Refinery Gas

2.4.   LPG

2.5.   Naphtha

2.6.   Kerosene Type Jet Fuel

2.7.   Other Kerosene

2.8.   Gas/Diesel (Distillate Fuel Oil)

2.9.   Heavy Fuel Oil

2.10.   Bitumen (Including Orimulsion)

2.11.   Petroleum Coke

2.12.   Other Oil Products

3.   Natural Gas

4.   Renewable Energy and Energy from Waste

4.1.   Industrial Waste (Non-Renewable)

4.2.   Municipal Waste (Renewable)

4.3.   Municipal Waste (Non-Renewable)

4.4.   Solid biofuels

4.5.   Biogases

4.6.   Biodiesels

4.7.   Other Liquid Biofuels

3.2.2.    Electricity and heat consumption in the Energy Sector

1.   Total Energy Sector

Excludes own use by plant, used for pumped storage, heat pumps and electric boilers.

1.1.	Of which: Coal Mines

1.2.	Of which: Oil and Gas Extraction

1.3.	Of which: Patent Fuel Plants

1.4.	Of which: Coke Ovens

1.5.	Of which: BKB/PB Plants

1.6.	Of which: Gas Works

1.7.	Of which: Blast Furnaces

1.8.	Of which: Petroleum Refineries

1.9.	Of which: Nuclear Industry

1.10.

Of which: Coal Liquefaction Plants

1.11.

Of which: Liquefaction (LNG)/Regasification Plants

1.12.

Of which: Gasification Plants (biogas)

1.13.

Of which: Gas-to-Liquids

1.14.

Of which: Charcoal Production Plants

1.15.

Of which: Not Elsewhere Specified – Energy

3.2.3.    Energy end-use specification

1.   Industry Sector

1.1.	Of which: Iron and Steel

1.2.	Of which: Chemical and Petrochemical

1.3.	Of which: Non-Ferrous Metals

1.4.	Of which: Non-Metallic Minerals

1.5.	Of which: Transport Equipment

1.6.	Of which: Machinery

1.7.	Of which: Mining and Quarrying

1.8.	Of which: Food, Beverages and Tobacco

1.9.	Of which: Pulp, Paper and printing

1.10.

Of which: Wood and Wood Products

1.11.

Of which: Construction

1.12.

Of which: Textile and Leather

1.13.

Of which: Not Elsewhere Specified – Industry

2.   Transport Sector

2.1.	Of which: Rail

2.2.	Of which: Pipeline transport

2.3.	Of which: Road

2.4.	Of which: Not Elsewhere Specified – Transport

3.   Residential Sector

3.1.	Residential, of which: Space heating

3.2.	Residential, of which: Space cooling

3.3.	Residential, of which: Water heating

3.4.	Residential, of which: Cooking

3.5.	Residential, of which: Lighting and electrical appliances This applies only to electricity.

3.6.	Residential, of which: Other end uses

4.   Commercial and Public Services

5.   Agriculture/Forestry

6.   Fishing

7.   Not Elsewhere Specified – Other

3.2.4.    Imports and exports

Imports and exports of energy quantities of electricity and heat by country.

3.2.5.    Net production of electricity generation and net heat production from autoproducers

Net production of electricity and net generation of heat from autoproducers of electricity generation and heat production are to be declared, for CHP plants, for electricity (only) plants and for heat (only) plants separately, in the following plants or activities:

1.   Total Energy Sector

1.1.	Of which: Coal Mines

1.2.	Of which: Oil and Gas Extraction

1.3.	Of which: Patent Fuel Plants

1.4.	Of which: Coke Ovens

1.5.	Of which: BKB/PB Plants

1.6.	Of which: Gas Works

1.7.	Of which: Blast Furnaces

1.8.	Of which: Petroleum Refineries

1.9.	Of which: Coal Liquefaction Plants

1.10.

Of which: Liquefaction (LNG)/Regasification Plants

1.11.

Of which: Gasification Plants (biogas)

1.12.

Of which: Gas-to-Liquids

1.13.

Of which: Charcoal Production Plants

1.14.

Of which: Not Elsewhere Specified – Energy

2.   Transport Sector

2.1.	Of which: Rail

2.2.	Of which: Pipeline transport

2.3.	Of which: Road

2.4.	Of which: Not Elsewhere Specified – Transport

3.   All other sectors: identical to the aggregate list as per ‘3.2.3 Energy end-use specification’.

3.3.    Structural data on electricity and heat generation

3.3.1.    Net Maximum Electrical Capacity And Peak Load

The capacity should be reported at 31 December of the relevant reported year.

Includes electrical capacity of both electricity (only) and CHP plants.

The Net Maximum Electrical Capacity is the sum of the net maximum capacities of all stations taken individually throughout a given period of operation. The period of operation assumed for present purposes is continuous running: in practice 15 hours or more per day. The net maximum capacity is the maximum power assumed to be solely active power that can be supplied, continuously, with all plant running, at the point of outlet to the network. The Peak Load is defined as the highest value of the power absorbed or supplied by a network or combination of networks within the country.

The Net Maximum Electrical Capacity must be declared for both main activity producers and autoproducers:

1.   Total

2.   Nuclear

3.   Hydro

3.1.	Of which: mixed plants

3.2.	Of which: pure pumped storage

4.   Geothermal

5.   Solar photovoltaic

6.   Solar thermal

7.   Tide, wave, ocean

8.   Wind

9.   Combustible fuels

9.1.	Of which: Steam

9.2.	Of which: Internal combustion

9.3.	Of which: Gas turbine

9.4.	Of which: Combined cycle

9.5.	Of which: Other To be specified if declared.

The following information about the peak load must be declared for the network:

10.   Peak load

11.   Available capacity at time of peak

12.   Date and time of peak load occurrence

3.3.2.    Net Maximum Electrical Capacity Of Combustible Fuels

Net maximum electrical capacity of combustible fuels must be declared for both main activity producers and autoproducers, and separately for each type of single-fired or multi-fired plant mentioned in the next table. Indications on which type of fuel is used as primary and alternate fuels must be added for all cases of multi-fired plants.

1.   Single Fuel Fired:

1.1.   Fired with Coal or coal products

Includes coke oven gas, blast furnace and oxygen steel furnace gas capacity.

1.2.   Fired with Liquids fuels

Includes refinery gas capacity.

1.3.   Fired with Natural gas

Includes gas works gas capacity.

1.4.   Fired with Peat

1.5.   Fired with Combustible renewables and wastes

2.   Multi-Fired, Solids And Liquids

3.   Multi-Fired, Solids And Natural Gas

4.   Multi-Fired, Liquids And Natural Gas

5.   Multi-Fired, Solids Liquids And Natural Gas

Multi-fired systems include only units which can burn more than one fuel type on a continuous basis. Stations which have separate units using different fuels should be divided into the appropriate single-fuel categories.

3.4.    Data on nuclear energy

The following data concerning the civil use of nuclear energy must be declared:

3.5.    Units of measurement

3.6.    Derogations and exemptions

France has a derogation for reporting the aggregates relating to heat. That derogation shall lapse as soon as France is able to forward this report and, at all events, no more than 4 years after the date of entry into force of this Regulation.

4.   OIL AND PETROLEUM PRODUCTS

4.1.    Applicable energy products

Unless otherwise specified this data collection applies to all of the following energy products:

4.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

4.2.1.    Supply of crude oil, NGL, refinery feedstocks, additives and other hydrocarbons

The following table applies to crude oil, natural gas liquids, refinery feedstocks, additives/oxygenates (and its bio part) and other hydrocarbons:

1.   Indigenous Production

Not applicable for refinery feedstocks and for biofuels.

2.

From Other Sources. Additives, Biofuels and Other hydrocarbons, the production of which has already been covered in other fuel balances. Not applicable for crude oil, NGL and refinery feedstocks. 2.1. Of which: from Coal Includes liquids produced from coal liquefaction plants, liquid output from coke ovens. 2.2. Of which: from Natural Gas The manufacture of synthetic gasoline may require natural gas as feedstock. The amount of gas for methanol manufacture is declared according to Chapter 2, while the receipts of methanol are declared here. 2.3. Of which: from Renewables Includes biofuels which are for blending with transport fuels. Production is declared as per Chapter 5, while amounts for blending are declared here.

3.	Backflows From Petrochemical Sector Finished or semi-finished products which are returned from final consumers to refineries for processing, blending or sale. They are usually by-products of petrochemical manufacturing. Only applicable for refinery feedstocks.

4.	Products Transferred Imported petroleum products which are reclassified as feedstocks for further processing in the refinery, without delivery to final consumers. Only applicable for refinery feedstocks.

5.

Imports and exports Includes quantities of crude oil and products imported or exported under processing agreements (i.e. refining on account). Crude oil and NGLs should be reported as coming from the country of ultimate origin; refinery feedstocks and finished products should be reported as coming from the country of last consignment. Includes any gas liquids (e.g. LPG) extracted during the regasification of imported liquefied natural gas and petroleum products imported or exported directly by the petrochemical industry. Note: All trade of biofuels which have not been blended with transport fuels (i.e. in their pure form) should be reported in the Renewables Questionnaire. Re-exports of oil imported for processing within bonded areas should be included as an export of product from the processing country to the final destination.

6.	Direct Use Crude oil, NGL, Additives and Oxygenates (and the part which are biofuels), and other hydrocarbons used directly without being processed in petroleum refineries. Includes crude oil burned for electricity generation.

7.	Stock changes A stock build is shown as a negative number and a stock draw is shown as a positive number.

8.	Calculated Refinery Intake Total amount of product calculated to have entered the refinery process. It is defined as: Indigenous production + From other sources + Backflows from industry + Products transferred + Imports – Exports – Direct use + Stock changes

9.	Statistical differences Defined as the calculated refinery intake minus the observed one.

10.	Observed Refinery Intake Amounts measured as input to refineries

11.	Refinery Losses The difference between Refinery intake (observed) and Gross refinery output. Losses may occur during the distillation processes due to evaporation. Reported losses are positive. There may be volumetric gains but no gains in mass.

12.

Opening and Closing Total Stocks On National Territory All stocks on national territory, including stocks held by governments, by major consumers or by stockholding organisations, stocks held on board incoming ocean vessels, stocks held in bonded areas and stocks held for others, whether under bilateral government agreement or not. Opening and closing refers to the first and to the last day of the reporting period respectively.

13.	Net Calorific Value Production, imports and exports, and overall average.

4.2.2.    Supply of oil products

The following table applies to finished products (refinery gas, ethane, LPG, naphtha, motor gasoline as well as its part of biogasoline, aviation gasoline, gasoline type jet fuel, kerosene type jet fuel as well as its bio part, other kerosene, gas/diesel oil, low and high sulphur fuel oil, white spirit and SBP, lubricants, bitumen, paraffin waxes, petroleum coke and other products). Crude oil and NGL used for direct burn should be included in deliveries of finished products and interproduct transfers.

1.   Primary Product Receipts

Includes quantities of indigenous or imported crude oil (including condensate) and indigenous NGL used directly without being processed in a petroleum refinery and quantities of Backflows from the Petrochemical industry which, although not primary fuel, are used directly.

2.   Gross Refinery Output

Production of finished products at a refinery or blending plant.

Excludes refinery losses, but includes Refinery fuel.

3.   Recycled Products

Finished products which pass a second time through the marketing network, after having been once delivered to final consumers (e.g. used lubricants which are reprocessed). These quantities should be distinguished from petrochemical Backflows.

4.   Refinery Fuel

Petroleum products consumed in support of the operation of a refinery.

Excludes products used by oil companies outside the refining process, e.g. bunkers or oil tankers.

Includes fuels used for the production at the refineries of electricity and heat sold.

4.1.	Of which: used for electricity generation Amounts used to generate electricity in plants at refineries.

4.2.	Of which: used for CHP production Amounts used in CHP plants at refineries.

4.3.	Of which: used for heat generation Amounts used to generate heat at refineries.

5.   Imports and Exports

6.   International Marine Bunkers

7.   Interproduct Transfers

Quantities reclassified either because their specification has changed or because they are blended into another product.

A negative entry for one product is compensated by a positive entry (or several entries) for one or several products and vice versa; the total net effect should be zero.

8.   Products Transferred

Imported petroleum products which are reclassified as feedstocks for further processing in the refinery, without delivery to final consumers.

9.   Stock Changes

A stock build is shown as a negative number and a stock draw is shown as a positive number.

10.   Calculated Gross Inland Deliveries

This is defined as:

Primary product receipts + Gross refinery output + Recycled products – Refinery fuel + Imports – Exports – International marine bunkers + Interproduct transfers – Products transferred + Stock changes

11.   Statistical Difference

Defined as the calculated gross inland delivery minus the observed one.

12.   Observed Gross Inland Deliveries

The observed delivery of finished petroleum products from primary sources (e.g. refineries, blending plants, etc.) to the inland market.

This figure may differ from the calculated figure due, for example, to differences in coverage and/or differences of definition in different reporting systems.

12.1.

Of which: Gross Deliveries To The Petrochemical Sector Quantities of fuels delivered to the Petrochemical sector.

12.2.

Of which: Energy Use In The Petrochemical Sector Quantities of oil used as fuel for petrochemical processes such as steam cracking.

12.3.

of which: Non-Energy Use In The Petrochemical Sector Quantities of oil used in the petrochemical sector for the purpose of producing ethylene, propylene, butylene, synthesis gas, aromatics, butadiene and other hydrocarbon-based raw materials in processes such as steam cracking, aromatics plants and steam reforming. Excludes amounts of oil used for fuel purposes.

13.   Backflows From Petrochemical Sector To Refineries

14.   Opening and Closing Stock Levels

All stocks on national territory, including stocks held by governments, by major consumers or by stockholding organisations, stocks held on board incoming ocean vessels, stocks held in bonded areas and stocks held for others, whether under bilateral government agreement or not. Opening and closing refers to the first and to the last day of the reporting period respectively.

15.   Stock Changes At Public Utilities

Changes in stocks which are held by public utilities and not included in the Stock levels and Stock changes reported elsewhere. A stock build is shown as a negative number and a stock draw is shown as a positive number.

Includes Crude oil and NGL used for direct burn, if applicable.

16.   Net Calorific Value Of Gross Inland Deliveries

4.2.3.    Gross inland deliveries by sector

In the now following tables, the following aggregates apply for crude oil, natural gas liquids, refinery gas, ethane, LPG, naphtha, total motor gasoline and its bio part, aviation gasoline, gasoline type jet fuel, total kerosene type jet fuel and its bio part, other kerosene, gas/diesel oil (and its fractions of road diesel, heating and other gas oil, biodiesels and Non-bio gas/diesel oil), total fuel oil (including its fractions of low and of high sulfur content), white spirit and SBP, lubricants, bitumen, paraffin waxes, petroleum coke, other oil products.

Both the quantities invloved for energy use and non-energy use and their total sum need to be declared.

1.   Total transformation Sector

Total quantities of fuels used for the primary or secondary conversion of energy.

1.1.	Of which: Main Activity Producer Electricity Plants

1.2.	Of which: Autoproducer Electricity plants

1.3.	Of which: Main Activity Producer CHP Plants

1.4.	Of which: Autoproducer CHP plants

1.5.	Of which: Main Activity Producer Heat Plants

1.6.	Of which: Autoproducer Heat plants

1.7.	Of which: Gas Works/Gasification Plants

1.8.	Of which: Blended Natural Gas

1.9.	Of which: Coke Ovens

1.10.

Of which: Blast Furnaces

1.11.

Of which: Petrochemical Industry

1.12.

Of which: Patent Fuel Plants

1.13.

Of which: Not Elsewhere Specified – Transformation

2.   Total Energy Sector

Total quantity used as energy in the energy sector

2.1.	Of which: Coal Mines

2.2.	Of which: Oil and Gas Extraction

2.3.	Of which: Coke Ovens

2.4.	Of which: Blast Furnaces

2.5.	Of which: Gas Works

2.6.	Of which: Power Plants Electricity, CHP and heat plants.

2.7.	Of which: Not Elsewhere Specified – Energy

3.   Distribution losses

Losses occurred outside the refinery due to transport and distribution.

Includes pipeline losses.

4.   Final Energy Consumption

5.   Industry Sector

5.1.	Of which: Iron and Steel

5.2.	Of which: Chemical and Petrochemical

5.3.	Of which: Non-Ferrous Metals

5.4.	Of which: Non-Metallic Minerals

5.5.	Of which: Transport Equipment

5.6.	Of which: Machinery

5.7.	Of which: Mining and Quarrying

5.8.	Of which: Food, Beverages and Tobacco

5.9.	Of which: Pulp, Paper and printing

5.10.

Of which: Wood and Wood Products

5.11.

Of which: Construction

5.12.

Of which: Textile and Leather

5.13.

Of which: Not Elsewhere Specified – Industry

6.   Transport Sector

6.1.	Of which: International Aviation

6.2.	Of which: Domestic Aviation

6.3.	Of which: Road

6.4.	Of which: Rail

6.5.	Of which: Domestic Navigation

6.6.	Of which: Pipeline Transport

6.7.	Of which: Not Elsewhere Specified – Transport

7.   Other Sectors

7.1.	Of which: Commercial and Public Services

7.2.	Of which: Residential 7.2.1. Residential, of which: Space heating 7.2.2. Residential, of which: Space cooling 7.2.3. Residential, of which: Water heating 7.2.4. Residential, of which: Cooking 7.2.5. Residential, of which: Other end uses

7.3.	Of which: Agriculture/Forestry

7.4.	Of which: Fishing

7.5.	Of which: Not Elsewhere Specified – Other

8.   Total Non-Energy Use

Quantities used as raw materials in the different sectors and not consumed as a fuel or transformed into another fuel. These quantities are included into the aggregates listed above.

8.1.	Of which: Transformation Sector

8.2.	Of which: Energy Sector

8.3.	Of which: Transport Sector

8.4.	Of which: Industry Sector 8.4.1 Industry Sector of which: Chemical (incl. Petrochemical)

8.5.	Of which: Other Sectors

4.2.4.    Imports and exports

Imports by country of origin, and exports by country of destination. See also notes under point 4.2.1, aggregate 5.

4.3.    Units of measurement

4.4.    Derogations and exemptions

Cyprus is exempted from reporting the aggregates defined in Section 4.2.3 under point 7 (Other Sectors) and point 8 (Total Non-Energy Use); only the total values shall be applicable.

5.   RENEWABLE ENERGY AND ENERGY FROM WASTE

5.1.    Applicable energy products

Unless otherwise specified this data collection applies to all of the following energy products:

5.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

5.2.1.    Gross Electricity and Heat Production

Electricity and heat produced from the energy products mentioned in Section 5.1 (except charcoal, biogasoline and bio jet kerosene) must be declared, wherever applicable, separately:

This requirement excludes charcoal. For the liquid biofuels, it excludes the biogasoline and the bio jet kerosene. For the hydro, declarations must be subdivided in plants with electrical output up 1 MW, between 1 and 10 MW, and above 10 MW.

5.2.2.    Supply and Transformation Sectors

Quantities of energy products that are mentioned in Section 5.1 (except for hydro power, solar photovoltaic energy, energy from tides, waves and oceans and wind energy) and used in the Supply and Transformation Sectors must be declared for the following aggregates:

1.   Production

2.   Imports

3.   Exports

4.   Stock changes

A stock build is shown as a negative number and a stock draw is shown as a positive number.

5.   Gross consumption

6.   Statistical differences

7.   Total transformation Sector

Quantities of renewables and wastes used for the conversion of primary forms of energy to secondary (e.g. landfill gases to electricity) or used for the transformation to derived energy products (e.g.: biogas used for blended natural gas).

7.1.	Of which: Main Activity Producer Electricity Plants

7.2.	Of which: Main Activity Producer CHP Plants

7.3.	Of which: Main Activity Producer Heat Plants

7.4.	Of which: Autoproducer Electricity plants

7.5.	Of which: Autoproducer CHP plants

7.6.	Of which: Autoproducer Heat plants

7.7.	Of which: Patent Fuel Plants Quantities of renewables and wastes used to produce patent fuel. Renewables and wastes used for heating and operation of equipment must be reported as consumption in the Energy sector.

7.8.	Of which: BKB/PB Plants Quantities of renewables and wastes used to produce BKB. Renewables and wastes used for heating and operation of equipment must be reported as consumption in the Energy sector.

7.9.	Of which: Gas Works Gas Quantities of renewables and wastes used to produce gas works gas. Renewables and wastes used for heating and operation of equipment must be reported as consumption in the Energy sector.

7.10.

Of which: blast furnaces Quantities of renewable energy (e.g. charcoal) transformed in blast furnaces. Renewable energy used for heating and operations of equipment should not be reported here, but reported as consumption in the Energy sector.

7.11.

Of which: Natural gas blending plants Quantities of biogases blended with natural gas which are injected to the natural gas network.

7.12.

Of which: blending with Motor gasoline/Diesel/Kerosene Quantities of liquid biofuels which are not delivered to the final consumption but are used with other petroleum products reported in the oil questionnaire.

7.13.

Of which: Charcoal production plants Quantities of wood used for the production of Charcoal.

7.14.

Of which: Not Elsewhere Specified – Transformation

5.2.3.    Energy Sector

Quantities of energy products that are mentioned in Section 5.1 (except for hydro power, solar photovoltaic energy, energy from tides, waves and oceans and wind energy) and used in the energy sector or for final consumption must be declared for the following aggregates:

1.   Total Energy Sector

Renewable energies and wastes consumed by the energy industry to support the transformation activity. For example renewable energies and wastes used for heating, lighting or operating pumps/compressors.

Quantities of renewable energies and wastes transformed into another energy form should be reported under the Transformation sector.

1.1.	Of which: Gasification plants

1.2.	Of which: Public Electric, CHP & Heat plants

1.3.	Of which: Coal Mines

1.4.	Of which: Patent Fuel Plants

1.5.	Of which: Coke Ovens

1.6.	Of which: Petroleum Refineries

1.7.	Of which: BKB/PB Plants

1.8.	Of which: Gas Works Gas

1.9.	Of which: Blast Furnaces

1.10.

Of which: Charcoal production plants

1.11.

Of which: Not Elsewhere Specified

2.   Distribution Losses

All losses occurred due to transport and distribution.

5.2.4.    Energy end-use

Quantities of energy products that are mentioned in Section 5.1 (except for hydro power, solar photovoltaic energy, energy from tides, waves and oceans and wind energy) must be declared for the following aggregates:

1.   Final Energy Consumption

2.   Industry Sector

2.1.	Of which: Iron and Steel

2.2.	Of which: Chemical and Petrochemical

2.3.	Of which: Non-Ferrous Metals

2.4.	Of which: Non-Metallic Minerals

2.5.	Of which: Transport Equipment

2.6.	Of which: Machinery

2.7.	Of which: Mining and Quarrying

2.8.	Of which: Food, Beverages and Tobacco

2.9.	Of which: Pulp, Paper and printing

2.10.

Of which: Wood and Wood Products

2.11.

Of which: Construction

2.12.

Of which: Textile and Leather

2.13.

Of which: Not Elsewhere Specified – Industry

3.   Transport Sector

3.1.	Of which: Rail

3.2.	Of which: Road

3.3.	Of which: Domestic Navigation

3.4.	Of which: Not Elsewhere Specified – Transport

4.   Other Sectors

4.1.	Of which: Commercial and Public Services

4.2.	Of which: Residential 4.2.1. Residential, of which: Space heating 4.2.2. Residential, of which: Space cooling 4.2.3. Residential, of which: Water heating 4.2.4. Residential, of which: Cooking 4.2.5. Residential, of which: Other end uses

4.3.	Of which: Agriculture/Forestry

4.4.	Of which: Fishing

4.5.	Of which: Not Elsewhere Specified – Other

5.2.5.    Technical Characteristics of Installations

The following electricity generation capacities are to be declared as applicable at the end of the reported year:

1.   Hydro power

Capacity must be reported for plant sizes of < 1 MW, 1 to < 10 MW, ≥ 10 MW, for mixed plants and for pure pumped storage, as well as for all sizes combined. Detailed plant sizes should be reported net of pumped storage.

2.   Geothermal

3.   Solar Photovoltaic

4.   Solar Thermal

5.   Tide, Wave, Ocean

6.   Wind

7.   Industrial Waste (non-renewable)

8.   Municipal Waste

9.   Solid biofuels

10.   Biogases

11.   Biodiesels

12.   Other liquid Biofuels

The total surface installed of solar collectors is to be declared.

The following biofuel production capacities are to be declared:

1.   Biogasoline

2.   Biodiesels

3.   Bio jet kerosene

4.   Other Liquid Biofuels

5.2.6.    Imports and exports

Imports by country of origin, and exports by country of destination are to be declared for the following products:

1.   Biogasoline

1.1.	Of which: Bioethanol

2.   Bio jet kerosene

3.   Biodiesels

4.   Other Liquid Biofuels

5.   Wood pellets

5.2.7.    Production of solid biofuels and biogases

The production of the following products is to be declared:

1.   Solid biofuels (excluding charcoal)

1.1.	Of which: fuelwood, wood residues and by-products 1.1.1. From fuelwood, wood residues and by-products, of which: wood pellets

1.2.	Of which: black liquor

1.3.	Of which: bagasse

1.4.	Of which: animal waste

1.5.	Of which: other vegetal materials and residues

2.   Biogases from anaerobic fermentation

2.1.	Of which: landfill gas

2.2.	Of which: sewage sludge gas

2.3.	Of which: other biogases from anaerobic fermentation

3.   Biogases from thermal proceses

5.3.    Calorific values

Average net calorific values are to be declared for the following products:

1.   Biogasoline

2.   Bioethanol

3.   Biodiesel

4.   Bio jet kerosene

5.   Other liquid biofuels

6.   Charcoal

5.4.    Units of measurement

5.5.    Derogations and exemptions

Not applicable.

6.   APPLICABLE PROVISIONS

The following provisions apply for the data collection as described in all preceding chapters:

1.	Reported period: A calendar year (1 January to 31 December).

2.	Frequency Annual.

3.	Deadline for transmission of data 30 November of the year following the reported period.

4.	Transmission format and method The transmission format shall conform to an appropriate interchange standard specified by Eurostat. Data shall be transmitted or uploaded by electronic means to the single entry point for data at Eurostat.

▼M2

---

ANNEX C

MONTHLY ENERGY STATISTICS

This Annex describes the scope, units, reported period, frequency, deadline and transmission modalities for the monthly collection of energy statistics.

Annex A applies for explanations of terms for which a specific explanation is not supplied in this Annex.

1.   SOLID FUELS

1.1.    Applicable energy products

Unless otherwise specified this data collection applies to all of the following energy products:

1.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

Annex A applies for explanations of terms for which a specific explanation is not supplied in this Annex.

1.2.1.    Supply Sector

The following aggregates apply to hard coal, lignite and peat:

1.   Production

2.   Recovered products (applies to hard coal only)

Slurries and waste-heap shale recovered by mines.

3.   Total imports

4.   Total exports

5.   Stocks:

These are the quantities held by mines and importers.

Excludes consumer stocks (e.g. those held in power stations and coking plants) except stocks held by consumers who import directly.

A stock build is shown as a negative number and a stock draw is shown as a positive number.

6.	Calculated Inland Deliveries. Total amount of product calculated to have been delivered for inland consumption. It is defined as:

7.	Statistical difference. Equals to calculated minus observed inland deliveries. Applies to hard coal only.

8.

Observed Internal Deliveries. Quantities delivered to the internal market. Equal to the total of the deliveries to the different types of consumers. A difference may occur between the calculated and observed deliveries. Applies to hard coal only. 8.1. Of which: deliveries to main activity producer power stations 8.2. Of which: deliveries to coking plants 8.3. Of which: deliveries to Patent fuel plants Quantities used for transformation in patent fuels plants (pithead and independent). 8.4. Of which: deliveries to total industry 8.5. Of which: other deliveries (services, households, etc.) Quantities of fuel to households (including colliery coal supplied to workers in mines and associated plants) and services (administrations, shops, etc.) and also to sectors not elsewhere specified.

The following aggregates apply to coke, patent fuels and brown coal briquettes:

1.	Production

2.	Total imports

3.	Total exports

4.

Stocks: — Beginning of period — End of period — Stock changes Quantities held in coking plants (coke) and patent fuel plants (patent fuels). Excludes consumers' stocks excepted stocks held by consumers which import directly. A stock build is shown as a negative number and a stock draw is shown as a positive number.

5.	Calculated Inland Deliveries Total amount of product calculated to have been delivered for inland consumption. It is defined as:

6.	Deliveries to Iron & steel industry (applies to coke only)

1.2.2.    Imports

Imports by country of origin and exports by country of destination are to be declared for hard coal.

1.3.    Units of measurement

All product quantities are expressed in 103 tonnes.

1.4.    Derogations and exemptions

Not applicable.

2.   ELECTRICITY

2.1.    Applicable energy products

This chapter covers electrical energy.

2.2.    List of aggregates

The following list of aggregates shall be declared.

2.2.1.    Production Sector

For the following aggregates both gross and net quantities must be declared:

1.   Total electricity production

1.1.	Of which: Nuclear

1.2.	Of which: Hydro 1.2.1. From 1.2, of which: part of hydro produced from pumped storage

1.3.	Of which: Geothermal

1.4.	Of which: Conventional thermal

1.5.	Of which: Wind

Also the following quantities of electrical energy must be declared:

2.   Imports

2.1.	Of which: intra-EU imports

3.   Exports

3.1.	Of which: extra-EU exports

4.   Used for pumped storage

5.   Used for the internal market

This is calculated as:

For the fuel consumption in main activity producer plants the following aggregates apply (refer to Annex B for the definition of lignite and Annex C for the definition of hard coal):

6.   Total fuel consumption in main activity producer plants

Total quantity of fuel consumed for the purpose of producing electricity and also for the production of heat to be sold to third parties exclusively.

6.1.	Of which: Hard coal

6.2.	Of which: Lignite

6.3.	Of which: Petroleum products

6.4.	Of which: Natural gas

6.5.	Of which: Derived gas (these are manufactured gases)

6.6.	Of which: Other fuels

2.2.2.    Fuel stocks in main activity producers

By main activity producers are meant public utilities generating electricity by using fuels. The following closing stocks (stocks at the end of the reported month) must be declared:

1.   Hard coal

2.   Lignite

3.   Petroleum products

2.3.    Units of measurement

2.4.    Derogations and exemptions

Not applicable.

3.   OIL AND PETROLEUM PRODUCTS

3.1.    Applicable energy products

Unless otherwise specified this data collection applies to all of the following energy products, for which the definitions in Annex B Chapter 4 apply: crude oil, NGL, refinery feedstocks, other hydro-carbons, refinery gas (not liquefied), ethane, LPG, naphtha, motor gasoline, aviation gasoline, gasoline type jet fuel (naphtha type jet fuel or JP4), kerosene type jet fuel, other kerosene, gas/diesel oil (distillate fuel oil), transport diesel, heating and other gasoil, fuel oil (both low and high sulphur content), white spirit and SBP, lubricants, bitumen, paraffin waxes and petroleum coke.

Where applicable, motor gasoline must be declared in two categories namely biogasoline and non-biogasoline; jet kerosene must be declared in two categories namely bio jet kerosene and non-bio jet kerosene; gas/diesel oil must be declared in four categories namely road diesel, heating and other gas oil, biodiesels and non-bio gas/diesel oil.

‘Other Products’ include both the quantities that correspond to the definition in Annex B Chapter 4) and in addition the quantities of white spirit and SBP, lubricants, bitumen and paraffin waxes; these products must not be declared separately.

3.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

3.2.1.    Supply Sector

The following table applies only to crude oil, NGL, refinery feedstocks, additives/oxygenates, biofuels and other hydrocarbons only:

1.   Indigenous Production

Not applicable for refinery feedstocks.

2.   From Other Sources

Additives, Biofuels and Other hydrocarbons, the production of which has already been covered in other fuel balances.

Not applicable for crude oil, NGL and refinery feedstocks.

3.   Backflows From Petrochemical Sector

Finished or semi-finished products which are returned from final consumers to refineries for processing, blending or sale. They are usually by-products of petrochemical manufacturing. Only applicable for refinery feedstocks.

4.   Products Transferred

Imported petroleum products which are reclassified as feedstocks for further processing in the refinery, without delivery to final consumers.

Only applicable for refinery feedstocks.

5.   Imports and exports

Includes quantities of crude oil and products imported or exported under processing agreements (i.e. refining on account). Crude oil and NGLs should be reported as coming from the country of ultimate origin; refinery feedstocks and finished products should be reported as coming from the country of last consignment.

Includes any gas liquids (e.g. LPG) extracted during the regasification of imported liquefied natural gas and petroleum products imported or exported directly by the petrochemical industry.

Note: All trade of biofuels which have not been blended with transport fuels (i.e. in their pure form) should be reported in the Renewables Questionnaire.

6.   Direct Use

Crude oil, NGL and Other hydrocarbons used directly without being processed in petroleum refineries.

Includes crude oil burned for electricity generation.

7.   Stock changes

A stock build is shown as a positive number and a stock draw is shown as a negative number.

8.   Calculated Refinery Intake

Total amount of product calculated to have entered the refinery process. It is defined as:

9.   Statistical differences

Defined as the calculated refinery intake minus the observed one.

10.   Observed Refinery Intake

Amounts measured as input to refineries

11.   Refinery Losses

The difference between Refinery intake (observed) and Gross refinery output. Losses may occur during the distillation processes due to evaporation. Reported losses are positive. There may be volumetric gains but no gains in mass.

The following table does not apply to refinery feedstocks nor to additives/oxygenates:

1.   Primary Product Receipts

Includes quantities of indigenous or imported crude oil (including condensate) and indigenous NGL used directly without being processed in a petroleum refinery and quantities of Backflows from the Petrochemical industry which, although not primary fuel, are used directly.

2.   Gross Refinery Output

Production of finished products at a refinery or blending plant.

Excludes refinery losses, but includes Refinery fuel.

3.   Recycled Products

Finished products which pass a second time through the marketing network, after having been once delivered to final consumers (e.g. used lubricants which are reprocessed). These quantities should be distinguished from petrochemical Backflows.

4.   Refinery Fuel

Petroleum products consumed in support of the operation of a refinery.

Excludes products used by oil companies outside the refining process, e.g. bunkers or oil tankers.

Includes fuels used for the production at the refineries of electricity and heat sold.

5.   Imports and Exports

6.   International Marine Bunkers

7.   Interproduct Transfers

Quantities reclassified either because their specification has changed or because they are blended into another product.

A negative entry for one product is compensated by a positive entry (or several entries) for one or several products and vice versa; the total net effect should be zero.

8.   Products Transferred

Imported petroleum products which are reclassified as feedstocks for further processing in the refinery, without delivery to final consumers.

9.   Stock Changes

A stock build is shown as a positive number and a stock draw is shown as a negative number.

10.   Calculated Gross Inland Deliveries

This is defined as:

11.   Statistical Difference

Defined as the calculated gross inland delivery minus the observed one.

12.   Observed Gross Inland Deliveries

The observed delivery of finished petroleum products from primary sources (e.g. refineries, blending plants, etc.) to the inland market.

This figure may differ from the calculated figure due, for example, to differences in coverage and/or differences of definition in different reporting systems.

12.1.

Of which: Deliveries to International Civil Aviation

12.2.

Of which: Deliveries to main activity producer power plants

12.3.

Of which: Deliveries of Automotive LPG

12.4.

Of which: Deliveries (gross) to Petrochemical sector

13.   Backflows from Petrochemical sector to refineries

14.   Total net inland deliveries

3.2.2.    Stocks

The following opening and closing stocks must be declared for all energy products including for additives/oxygenates but except for refinery gas:

1.   Stocks on national territory

Stocks in the following locations: refinery tanks, bulk terminals, pipeline tankage, barges and coastal tankers (when port of departure and destination are in the same country), tankers in a port of a member country (if their cargo is to be discharged at the port), inland ship bunkers. Exclude stocks of oil held in pipelines, in rail tanks cars, in truck tanks cars, in sea-going ships' bunkers, in service stations, in retail stores and in bunkers at sea.

2.   Stocks held for other countries under bilateral government agreements

Stocks on national territory which belong to another country and to which the access is guaranteed by an agreement between the respective governments.

3.   Stocks with known foreign destination

Stocks not included in point 2 on national territory which belong to and are destined for another country. These stocks may be located inside or outside bonded areas.

4.   Other stocks held in bonded areas

Includes stocks not included in point 2 nor 3 irrespective of whether they have received customs clearance or not.

5.   Stocks held by major consumers

Include stocks which are subject to government control. This definition does not include other consumer stocks.

6.   Stocks held on board incoming ocean vessels in port or at mooring

Stocks irrespective of whether they have been cleared by customs or not. This category excludes stocks on board vessels at high seas.

Includes oil in coastal tankers if both their port of departure and destination are in the same country. In the case of incoming vessels with more than one port of unloading, only report the amount to be unloaded in the reporting country.

7.   Stocks held by government on national territory

Includes non-military stocks held within the national territory by government, which are government owned or controlled and held exclusively for emergency purposes.

Excludes stocks held by state oil companies or electric utilities or stocks held directly by oil companies on behalf of governments.

8.   Stocks held by stock holding organisation on national territory

Stocks held by both public and private corporations established to maintain stocks exclusively for emergency purposes.

Excludes mandatory stocks held by private companies.

9.   All other stocks held on national territory

All other stocks satisfying the conditions described in point 1 above.

10.   Stocks held abroad under bilateral government agreements

Stocks belonging to the reporting country but held in another country, to which access is guaranteed by an agreement between the respective governments.

10.1.

Of which: Government stocks

10.2.

Of which: Holding organisation's stocks

10.3.

Of which: Other stocks

11.   Stocks held abroad designated definitely for import stocks

Stocks not included in category 10 which belonging to the reporting state but which are held in another state and awaiting import there.

12.   Other stocks in bonded areas

Other stocks in the national territory not included in the above categories.

13.   Pipeline fill

Oil (crude oil and petroleum products) contained in pipelines, necessary to maintain the flow in the pipelines.

In addition, a breakdown of quantities per corresponding country must be declared for:

By opening stocks are meant the stocks on the last day of the month preceding the reported one. By closing stocks are meant the stocks on the last day of the reported month.

3.2.3.    Imports and exports

Imports by country of origin, and exports by country of destination.

3.3.    Units of measurement

Energy quantities: 103 tonnes

3.4.    Geographical notes

For statistical reporting purposes only, the clarifications of Annex A Chapter 1 apply with the following specific exceptions:

3.5.    Derogations and exemptions

Not applicable.

4.   NATURAL GAS

4.1.    Applicable energy products

Natural gas is defined in Annex B Chapter 2.

4.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

4.2.1.    Supply Sector

1.   Indigenous Production

All dry marketable production within national boundaries, including offshore production. Production is measured after purification and extraction of NGLs and sulphur.

Excludes extraction losses and quantities reinjected, vented or flared.

Includes quantities used within the natural gas industry; in gas extraction, pipeline systems and processing plants.

2.   Imports

3.   Exports

4.   Stock changes

A stock build is shown as a positive number and a stock draw is shown as a negative number.

5.   Calculated Gross Inland Deliveries

This is defined as:

6.   Statistical Difference

Defined as the calculated gross inland delivery minus the observed one.

7.   Observed Gross Inland Deliveries

Includes gas used by the gas industry for heating and operation of their equipment (i.e. consumption in gas extraction, in the pipeline system and in processing plants) and losses in distribution.

8.   Opening and closing levels of stocks held on national territory

Quantities stored in special storage facilities (depleted gas and/or oil field, aquifer, salt cavity, mixed caverns or other) as well as liquefied natural gas storage. By opening stocks are meant the stocks on the last day of the month preceding the reported one. By closing stocks are meant the stocks on the last day of the reported month.

9.   Own use and losses of the natural gas industry

Own used quantities by the gas industry for heating and operation of its equipment (i.e. consumption in gas extraction, in the pipeline system and in processing plants).

Includes losses in distribution.

4.2.2.    Imports and exports

Contrary to the definitions in Annexe A, imports and exports are to be declared by neighbouring country in this case.

4.3.    Units of measurement

Quantities must be declared in two units:

4.4.    Derogations and exemptions

Not applicable.

5.   APPLICABLE PROVISIONS

The following provisions apply for the data collection as described in all preceding chapters:

1.   Reported period:

A calendar month.

2.   Frequency

Monthly.

3.   Deadline for transmission of data

All data described under Section 3 (oil and petroleum products) and under Section 4 (natural gas): within 55 days following the reported month.

All other data: within three months following the reported month.

4.   Transmission format and method

The transmission format shall conform to an appropriate interchange standard specified by Eurostat.

Data shall be transmitted or uploaded by electronic means to the single entry point for data at Eurostat.

---

ANNEX D

SHORT TERM MONTHLY STATISTICS

This Annex describes the scope, units, reported period, frequency, deadline and transmission modalities for the short-term monthly collection of statistical data.

Annex A applies for explanations of terms for which a specific explanation is not supplied in this Annex.

1.   NATURAL GAS

1.1.    Applicable energy products

This chapter covers natural gas only. Natural gas is defined in chapter 2 of Annex B.

1.2.    List of aggregates

The following list of aggregates shall be declared.

1.   Production

2.   Imports

3.   Exports

4.   Stock change

A stock build is shown as a negative number and a stock draw is shown as a positive number.

5.   Supply

This is calculated as:

6.   Stocks at the end of month

1.3.    Units of measurement

Quantities of natural gas must be declared in TJ, based on the gross calorific value.

1.4.    Other applicable provisions

1.   Reported period:

A calendar month.

2.   Frequency

Monthly.

3.   Deadline for transmission of data

Within one month following the reported month.

4.   Transmission format and method

The transmission format shall conform to an appropriate interchange standard specified by Eurostat.

Data shall be transmitted or uploaded by electronic means to the single entry point for data at Eurostat.

1.5.    Derogations and exemptions

Germany has a derogation from this data collection until 30 September 2014.

2.   ELECTRICITY

2.1.    Applicable energy products

This chapter covers electricity only.

2.2.    List of aggregates

The following list of aggregates shall be declared.

1.   Total electricity production

Total gross quantity of electricity generated.

Includes own consumption of power plants.

2.   Imports

3.   Exports

4.   Gross electricity Supply

This is calculated as:

2.3.    Units of measurement

Energy quantities must be expressed in GWh

2.4.    Other applicable provisions

1.   Reported period:

A calendar month.

2.   Frequency

Monthly.

3.   Deadline for transmission of data

Within one month following the reported month.

4.   Transmission format and method

The transmission format shall conform to an appropriate interchange standard specified by Eurostat.

Data shall be transmitted or uploaded by electronic means to the single entry point for data at Eurostat.

2.5.    Derogations and exemptions

Germany is exempted from this data collection.

3.   OIL AND PETROLEUM PRODUCTS

This data collection is commonly known as the ‘JODI Questionnaire’.

3.1.    Applicable energy products

Unless otherwise specified, this data collection applies to all of the following energy products, for which the definitions in Chapter 4 of Annex B apply: crude oil, LPG, gasoline (which is the sum of motor gasoline and aviation gasoline), kerosene (which is the sum of kerosene type jet fuel and other kerosene), gas/diesel oil and fuel oil (both low and high sulphur content).

In addition, this data collection also applies to ‘total oil’, by which is meant the sum of all these products except crude oil, and must also include other petroleum products such as refinery gas, ethane, naphtha, petroleum coke, white spirit and SBP, paraffin waxes, bitumen, lubricants and others.

3.2.    List of aggregates

The following list of aggregates shall be declared for all energy products listed in the previous paragraph unless otherwise specified.

3.2.1.    Supply Sector

The following table applies only to crude oil:

1.   Production

2.   Imports

3.   Exports

4.   Closing Stock

5.   Stock change

A stock build is shown as a positive number and a stock draw is shown as a negative number.

6.   Refinery Intake

Observed refinery throughput.

The following table applies to crude oil, LPG, gasoline, kerosene, gas/diesel oil, fuel oil and total oil:

1.   Refinery Output

Gross output, including refinery fuel.

2.   Imports

3.   Exports

4.   Closing Stock

5.   Stock change

A stock build is shown as a positive number and a stock draw is shown as a negative number.

6.   Demand

Deliveries or sales to the inland market (domestic consumption) plus Refinery Fuel plus International Marine and Aviation Bunkers. Demand for Total Oil includes Crude.

3.3.    Units of measurement

Energy quantities: 103 tonnes

3.4.    Other applicable provisions

1.   Reported period:

A calendar month.

2.   Frequency

Monthly.

3.   Deadline for transmission of data

Within 25 days following the reported month.

4.   Transmission format and method

The transmission format shall conform to an appropriate interchange standard specified by Eurostat.

Data shall be transmitted or uploaded by electronic means to the single entry point for data at Eurostat.

3.5.    Derogations and exemptions

Not applicable.

---

( 1 ) Opinion of the European Parliament of 12 March 2008 (not yet published in the Official Journal) and Council Decision of 15 September 2008.

( 2 ) OJ L 49, 19.2.2004, p. 1.

( 3 ) OJ L 283, 27.10.2001, p. 33.

( 4 ) OJ L 52, 21.2.2004, p. 50.

( 5 ) OJ L 1, 4.1.2003, p. 65.

( 6 ) OJ L 114, 27.4.2006, p. 64.

( 7 ) OJ L 191, 22.7.2005, p. 29.

( 8 ) OJ C 317 E, 23.12.2006, p. 876.

( 9 ) OJ L 52, 22.2.1997, p. 1.

( 10 ) OJ L 181, 28.6.1989, p. 47.

( 11 ) OJ L 184, 17.7.1999, p. 23.

( 12 ) OJ L 55, 1.3.2005, p. 57.