Faravardeh Fooladi Co.

A very important issue for all of the clients that have shot blasting machines ... Do you know how much shot or grit is being thrown by the wheel during the blast cycle of your shot-blasting machine? By Reading the Value of the Ammeter and the table below, you can estimate the amount of abrasive flowing by the wheel; but this table is true when the Electrical motors are working under full load. If they do not work under full load, According to the high or low value read from the ammeter, you realize that enough steel shot is not flowing to wheels and there is a problem in your shot blasting machine. So other adjustments should be made. For more useful information about ammeter please read my paper on LinkedIn. 1- https://lnkd.in/dn9kh7xW <iframe src="https://lnkd.in/daE_ApCX" height="501" width="504" frameborder="0" allowfullscreen="" title="Embedded post"></iframe> #shotblasting#shotpeening# abrasive#wheels

Do you know when worn wheel parts should be changed? Since wear of turbine components causes changes in the projection pattern, turbine components should be checked daily for the extent of wear, and the following should be controlled: 1- Impeller: If the guide edges are worn over 1/8 inch, replace them. 2- Control cage: If the edges of the outlet valve are worn more than 1/4 inch, replace it. 3- Blades: If surface wear has occurred to half the thickness of the blade, replace the blades. www.ab-shot.ir

ARE YOU A SLEEPWALKER ?   THE SHOT-BLASTING INDUSTRY IS UNDER FIRE: -      The automotive foundries and forges are being decimated by the surge or 100% electric cars, -      By 2030, this is wiping out 70-80 KT of metallic abrasives and 35-40 million wheel-hours, -      And the sales of new shot-blast machines in automotive will drop by EUR 90-100 million, -      This will EXACERBATE THE COMPETITIVE PRESSURE across the board.   The 6th Shot-blasting Global Study is the last one, hence the final chance to gain access to the full picture of our industry: -      Quantification and forecast of 13 market drivers, -      Metallic abrasives usage (KT) and Wheel-hours (millions) in 128 countries, -      Competitive landscape (200 manufacturers and producers, many will drop out by 2030), -      Installed park of machines and yearly sales value of new equipment in 50 countries, -      Number of machines in operation by type, industry and application, -      Game changers such as the Sinto-Winoa merger, commoditization of medium-end machines, digital retrofittings, geopolitical reshufflings & more …   The OPPORTUNITIES TO GRAB FOR A PRESSING REDEPLOYMENT are key takeaways: -      Where the demand is growing, by application, industry, country etc. -      High definition coverage of the DEFENSE AND MILITARY OUTLETS, -      & more   WAKE UP AND LET ME KNOW IF YOU WANT A SAMPLE #shotblasting #shotpeening

Reliable parts, trusted partners. 🌟 Why we do it: We believe in empowering businesses to keep operations running smoothly with reliable, high-quality spare parts. 🔍 How we deliver: With a vast, well-stocked inventory and comprehensive archives, we’re able to meet specific needs quickly and effectively. 🔧 What we offer: As a trusted supplier for shot blast machine parts across various brands, we’re proud to be a partner our customers can rely on. #TrustedPartner #WhyWeDoIt #SpareParts #ShotBlastSolutions #Reliability #Shotblastengineering

Attention, very important…  Some experts believe that the quality of a coating depends more on the quality of its substrate than on the type of paint or primer. The quality and durability of any coating (paint or corrosion-resistant materials, etc.) highly depend on the workpiece's surface conditions. A paint or coating will have adequate adhesion on a surface only when the surface has microscopic cavities or, in other words, a specific roughness.  Therefore, before any painting or coating, these parts undergo a blasting process to clean the surface and remove contaminants from the parts, and the impact of abrasive materials slightly roughens the surface of the parts. The penetration of the paint into these rough surfaces increases the adhesion of the coating and the complete bond of the paint to the body. It should be noted that even steel sheets received from sheet manufacturers require preparation. Most of these steels are coated with oil to prevent corrosion, and in addition, there is usually a thin layer called the oxide layer on their surface, which over time turns into rust. All iron used for the construction of industrial sheds, ship hulls, aircraft, and even the body of most cars used in the world are cleaned and roughened in this way before painting. Blasting is also widely used in the oil industry, and all oil and gas pipelines must undergo blasting before being insulated with asphalt or corrosion-resistant coatings. www.ab-shot.ir #shotblasting#shotpeening

in many cases, the only reason for inadequate cleaning is attributed to the type and quality of the abrasive materials. However, abrasive materials are only one of the factors affecting this process. The most important factors influencing the achievement of proper cleaning are: • Abrasive materials (type, size, hardness, shape, microstructure, and material composition) • Abrasive blasting method (blasting speed, flow rate, projection angle, blasting width, blasting pattern, shot blasting process time) • Condition of all machine parts (separator, dust collector, elevators, etc.) • Maintenance, repair, and periodic inspections

Challenging Expectations: We believe in redefining value. With a vast archive, we make high-quality spare parts at affordable prices, because quality and affordability should never be a compromise. #Sinto

Integrated Manufacturing" We produce a wide range of steel abrasives and spare parts, all under one roof, ensuring a seamless solution for all your needs. www.ab-shot,ir #shotblasting

At the core of everything we do is a commitment to innovation. We strive to think outside the box, ensuring our products are not only highly functional but also thoughtfully crafted. Our passion for excellence drives us to create exceptional spare parts, designed with both form and function in mind.

if you want to obtain an effective and productive cleaning you should pay attention to adjusting the control cage ... www.ab-shot.ir