Akrivis Technologies’ Post

Surface hardening powder It is a powder for dry spraying on fresh concrete surfaces, which are used in order to create high resistance against chemicals, industrial substances, fats, industrial oils, detergents and hydraulic fluids that are used in the aviation industry. Continuous protection Against consecutive uses, it creates impact and wear for concrete surfaces. This material is used for the flooring of halls and areas of industrial factories, car loading and refueling platforms, shipyards, multi-store parking lots, power stations and places Installation of turbines and generators, car washes are used. #Concrete_Admixture #Concrete_Plasticizers #Waterproofin_Concrete #Grout #Protective_Coating #Construction_Adhesives #Flooring_Systems #Structures_Accessories #Plastic_Spacers #concrete #canada #canada_concrete #canada_concrete_clinic #Toronto #ndt_testing

What is pressure washing? Pressure washing is an essential first step of the coating process. It utilizes pressurized water and is commonly used for concrete, steel, and other substrates that are being prepped for coating. This process helps clean the substrate by removing a variety of visible and nonvisible contaminants. It is sometimes necessary to provide a higher level of substrate preparation, which may lead to abrasive blasting. Water pressure cleaning is categorized as follows: ·   Low pressure water cleaning is up to 5,000 PSI. ·   High pressure water cleaning is 5,000 - 10,000 PSI. ·   High pressure water jetting is 10,000 - 30,000 PSI. ·   Ultra-high pressure water jetting is over 30,000 PSI.   AMPP Water Jet (WJ) cleanliness standards are as follows: ·   WJ-1 - Clean to bare substrate. ·   WJ-2 - Very thorough cleaning. ·   WJ-3 - Thorough cleaning. ·   WJ-4 - Light cleaning. Email us at info@technocoatings.com or visit our website at www.technocoatings.com for more information on our services! #technocoatings #industrialcoatings #commercialcoatings #pressurewashing #flooring #coatings #waterpressure #ampp

A fire can cause soot and smoke damage to metal, brick and concrete and charring to wood. This type of damage is unsightly and holds odor. Traditionally, the removal method has been sanding, scraping and wire brushing. With Cold Jet, this long and tedious process can be eliminated. Cold Jet dry ice blasting has become the preferred method to remove smoke soot, vaporized synthetic resins and char. It has even been known to reduce or eliminate the musty burnt smell that results from fire, smoke and water damage. Cold Jet dry ice blasting provides a fast and efficient removal of smoke damage even in the tight angles of trusses, around nails, wiring and all plumbing without damage to the surface integrity. Cleaning with Cold Jet Dry Ice Blasting Technology Provides: Cleaning with Cold Jet Dry Ice Blasting in The Food Industry Provides: ✔️No secondary waste ✔️Reduced cleaning time (up to 80%) ✔️Increase in Quality standards ✔️Clean in-place, no cool down, with minimal disassembly ✔️A non-abrasive clean that won’t damage substrates ✔️Non-conductive process ✔️Media entrapment elimination ✔️Increased operator safety ✔️An environmentally responsible clean 𝐖𝐚𝐧𝐭 𝐭𝐨 𝐤𝐧𝐨𝐰 𝐦𝐨𝐫𝐞 𝐚𝐛𝐨𝐮𝐭 𝐨𝐮𝐫 𝐃𝐫𝐲 𝐈𝐜𝐞 𝐂𝐥𝐞𝐚𝐧𝐢𝐧𝐠 𝐓𝐞𝐜𝐡𝐧𝐨𝐥𝐨𝐠𝐲? 𝐂𝐚𝐥𝐥: ✆ 𝟏𝟑𝟎𝟎 𝐂𝐎𝐋𝐃𝐉𝐄𝐓 / +𝟔𝟏𝟐 𝟗𝟔𝟎𝟎 𝟗𝟓𝟕𝟎 𝐄𝐦𝐚𝐢𝐥: 𝐢𝐧𝐟𝐨@𝐜𝐨𝐥𝐝𝐣𝐞𝐭.𝐜𝐨𝐦.𝐚𝐮 #FireRestoration #DryIceBlasting #ColdJetAustralia

FSV heat sealing foil (Foil-scrim-PE) / Heat-sealing foil lamination is suitable for lamination of glasswool, rockwool, mineral wool insulation. FSV has thicker heat-sealable PE with good corrosion resistance. There is no need applying extra adhesive. Black coating with fireproof & anti-corrosion performance can be added for the aluminum foil. It is commonly used in applications requiring moisture resistance, such as in construction for vapor barriers, roofing, or insulation materials. It's often used to protect surfaces from dampness while offering durability and flexibility.  #moisturebarrier #waterproofing #easyapplication     #dustcontrol  #constructionmaterials  #noncombustible    #dustbarrier  #Wuxitago #Tagofoil #Aluminumfoil #Alufoil

Wet slurry blasting is significantly cleaner than other forms of blasting. The slurry of abrasive materials utilized during wet blasting can thoroughly blast a wide range of surfaces. Wet slurry blasting requires less post-job cleanup because it combines water with abrasive materials to prepare, polish, and/or reshape surfaces. It also utilizes only 150-250 lbs of abrasive per hour; leaving less to pick up at the end of the project. #GBT #greenerblast #sandblasting #resurface #sandblasting #abrasiveblasting #abrasives #blasting #manufacturing #abrasivesolutions #carrepair #industrialbusiness #industrialwork #distributors #blastingunit #mobileblasting #surfacepreparation #surfacepreparationmachine

Here is one of our trommel screeners cleaning wet, mucky, sticky fines from wood debris. Our west coast weather can be challenging at times. With this unit, we were able to clean up this pile and separate the clean wood for further grinding. No need to pay the extra storage fees to wait for dry weather (ie summer). Have you ever thought of the extra costs incurred by grinding material that is already to size or that shouldn’t be there is the first place? The extra wear, fuel and hours etc? Running a fuel efficient trommel like this not only saves your grinder this extra wear, it allow you to keep the dirt/soil/rocks on sites. You end up with a Cleaner and more useable end wood product and save trucking costs by being able to leave those site materials on site. What stands these trommels apart from the others? 1. Fuel efficiency- these are run with variable displacement hydraulic pumps. That means it only pumps the oil it needs! Less HP, less cooling needs, less fuel and ultimately less $. 2. Punch plate drum with spiral/worm auger to control the flow of material thru the drum. Notice how the material is not being lifted to 12 o’clock and dropped? The punch plate steel is smooth, unlike the woven mesh wrapped drums. This allows the material to glide along the screen and ensure maximum contact for maximum screening productivity and efficiency. 3. Adjustability. There is an infinite amount of adjustment to suit your products being screened. Feed speed, drum rpm, brushes to clean that drum, drum angle to name a few. 4. Load sensing drum with feeder interaction. What this means is the load in the drum is measured by pressure. This load sense can be adjusted to suit your material. Once the pressure limit is hit, the feeder slows down and even stops. It will restart when that pressure limit falls below that setting. This means the drum is never too full or too empty, keeping your material consistent! On site recommendations available. Call or text 604-991-9779

A fire can cause soot and smoke damage to metal, brick and concrete and charring to wood. This type of damage is unsightly and holds odor. Traditionally, the removal method has been sanding, scraping and wire brushing. With Cold Jet, this long and tedious process can be eliminated. Cold Jet dry ice blasting has become the preferred method to remove smoke soot, vaporized synthetic resins and char. It has even been known to reduce or eliminate the musty burnt smell that results from fire, smoke and water damage. Cold Jet dry ice blasting provides a fast and efficient removal of smoke damage even in the tight angles of trusses, around nails, wiring and all plumbing without damage to the surface integrity. Traditional cleaning methods are time consuming and tedious, not to mention ineffective for complete removal. Dry ice cleaning is up to three times faster than traditional methods!!!. Cleaning with Cold Jet Dry Ice Blasting in a Fire Restoration Provides: ✔️No secondary waste ✔️Reduced cleaning time (up to 80%) ✔️Increase in Quality standards ✔️Clean in-place, no cool down, with minimal disassembly ✔️A non-abrasive clean that won’t damage substrates ✔️Non-conductive process ✔️Media entrapment elimination ✔️Increased operator safety ✔️An environmentally responsible clean 𝐖𝐚𝐧𝐭 𝐭𝐨 𝐤𝐧𝐨𝐰 𝐦𝐨𝐫𝐞 𝐚𝐛𝐨𝐮𝐭 𝐨𝐮𝐫 𝐃𝐫𝐲 𝐈𝐜𝐞 𝐂𝐥𝐞𝐚𝐧𝐢𝐧𝐠 𝐓𝐞𝐜𝐡𝐧𝐨𝐥𝐨𝐠𝐲? 𝐂𝐚𝐥𝐥: ✆ 𝟏𝟑𝟎𝟎 𝐂𝐎𝐋𝐃𝐉𝐄𝐓 / +𝟔𝟏𝟐 𝟗𝟔𝟎𝟎 𝟗𝟓𝟕𝟎 𝐄𝐦𝐚𝐢𝐥: 𝐢𝐧𝐟𝐨@𝐜𝐨𝐥𝐝𝐣𝐞𝐭.𝐜𝐨𝐦.𝐚𝐮 #FireRestoration #DryIceBlasting #ColdJetAustralia

The Cold Vulcanizing Kit GB-3150 (FR Grade) with KRE Hardener is the ultimate solution for joining fire-resistant conveyor belts. Regular cold vulcanizing kits just can’t handle the heat and strength required for HR, FR, and CR grade belts, which can withstand temperatures up to 180°C. When using subpar kits, the joints break under stress, leading to costly delays and damage to your manufacturing process. Don’t settle for less—choose our GB-3150 Cement with KRE Hardener for superior performance. This 1kg tin pack, paired with the 70gm Aluminium Bottle of KRE Hardener, ensures your conveyor belts stay strong, safe, and efficient. Ideal for high-temperature environments, our cold vulcanizing kit delivers durable, fire-resistant joints that will keep your system running smoothly. Why risk it with ordinary kits when you can have the best? Trust Oliver Rubber LLP for all your conveyor belt maintenance needs. Our products are designed for long-lasting, high-performance results in even the toughest industrial conditions. For more information, visit: www.oliverllp.com Contact: +91 94141 29472 Email: Export@oliverrubber.in #ColdVulcanizingKit #ConveyorBeltMaintenance #FireResistantBelts #OliverRubberLLP #GB3150 #KREHardener #IndustrialMaintenance #ConveyorBeltRepair #HeatResistant #RubberSolution #ManufacturingEfficiency

There's simply not a better way to remove soot and complex chemical compounds from brick, wood, and other substrates than dry ice blasting. A fire can cause soot and smoke damage to metal, brick and concrete and charring to wood. This type of damage is unsightly and holds odor. Traditionally, the removal method has been sanding, scraping and wire brushing. With Cold Jet, this long and tedious process can be eliminated. Cold Jet dry ice blasting has become the preferred method to remove smoke soot, vaporized synthetic resins and char. It has even been known to reduce or eliminate the musty burnt smell that results from fire, smoke and water damage. Cold Jet dry ice blasting provides a fast and efficient removal of smoke damage even in the tight angles of trusses, around nails, wiring and all plumbing without damage to the surface integrity. Cleaning with Cold Jet Dry Ice Blasting Provides: ✔️No secondary waste ✔️Reduced cleaning time (up to 80%) ✔️Increase in Quality standards ✔️Clean in-place, no cool down, with minimal disassembly ✔️A non-abrasive clean that won’t damage substrates ✔️Non-conductive process ✔️Media entrapment elimination ✔️Increased operator safety ✔️An environmentally responsible clean 𝐖𝐚𝐧𝐭 𝐭𝐨 𝐤𝐧𝐨𝐰 𝐦𝐨𝐫𝐞 𝐚𝐛𝐨𝐮𝐭 𝐨𝐮𝐫 𝐃𝐫𝐲 𝐈𝐜𝐞 𝐂𝐥𝐞𝐚𝐧𝐢𝐧𝐠 𝐓𝐞𝐜𝐡𝐧𝐨𝐥𝐨𝐠𝐲? 𝐂𝐚𝐥𝐥: ✆ 𝟏𝟑𝟎𝟎 𝐂𝐎𝐋𝐃𝐉𝐄𝐓 / +𝟔𝟏𝟐 𝟗𝟔𝟎𝟎 𝟗𝟓𝟕𝟎 𝐄𝐦𝐚𝐢𝐥: 𝐢𝐧𝐟𝐨@𝐜𝐨𝐥𝐝𝐣𝐞𝐭.𝐜𝐨𝐦.𝐚𝐮 #SmokeSootRemoval #DryIceBlasting #ColdJetAustralia

A fire can cause soot and smoke damage to metal, brick and concrete and charring to wood. This type of damage is unsightly and holds odor. Traditionally, the removal method has been sanding, scraping and wire brushing. With Cold Jet, this long and tedious process can be eliminated. Cold Jet dry ice blasting has become the preferred method to remove smoke soot, vaporized synthetic resins and char. It has even been known to reduce or eliminate the musty burnt smell that results from fire, smoke and water damage. Cold Jet dry ice blasting provides a fast and efficient removal of smoke damage even in the tight angles of trusses, around nails, wiring and all plumbing without damage to the surface integrity. Traditional cleaning methods are time consuming and tedious, not to mention ineffective for complete removal. Dry ice cleaning is up to three times faster than traditional methods!!!. Cleaning with Cold Jet Dry Ice Blasting in a Fire Restoration Provides: ✔️No secondary waste ✔️Reduced cleaning time (up to 80%) ✔️Increase in Quality standards ✔️Clean in-place, no cool down, with minimal disassembly ✔️A non-abrasive clean that won’t damage substrates ✔️Non-conductive process ✔️Media entrapment elimination ✔️Increased operator safety ✔️An environmentally responsible clean ❄️𝐖𝐚𝐧𝐭 𝐭𝐨 𝐤𝐧𝐨𝐰 𝐦𝐨𝐫𝐞 𝐚𝐛𝐨𝐮𝐭 𝐨𝐮𝐫 𝐃𝐫𝐲 𝐈𝐜𝐞 𝐂𝐥𝐞𝐚𝐧𝐢𝐧𝐠 𝐓𝐞𝐜𝐡𝐧𝐨𝐥𝐨𝐠𝐲? 𝐂𝐚𝐥𝐥: ✆ 𝟏𝟑𝟎𝟎 𝐂𝐎𝐋𝐃𝐉𝐄𝐓 / +𝟔𝟏𝟐 𝟗𝟔𝟎𝟎 𝟗𝟓𝟕𝟎 𝐄𝐦𝐚𝐢𝐥: 𝐢𝐧𝐟𝐨@𝐜𝐨𝐥𝐝𝐣𝐞𝐭.𝐜𝐨𝐦.𝐚𝐮 #FireRestoration #ColdJetAustralia #DryIceBlasting