KingsMen Electrical Services’ Post

Design process for a step-up Air-Insulated Substation (AIS) connected to a solar PV plant This methodology explains how to construct a step-up air-insulated substation (AIS) that is connected to a solar power plant. This document’s principal goal is to outline the key actions required to ascertain a substation’s electrical properties. A substation can be constructed in numerous different ways. Advantages and drawbacks would exist for each approach https://lnkd.in/dRdsikxF

Transmission lines for solar plants are designed to carry electrical energy generated by solar panels to the power grid or a substation. Here are some key considerations of my today's learning. 1. Voltage level : Typically ranges from 34.5 kV to 765 kV. 2. Conductor selection : Aluminum or ACSR (Aluminum Conductor Steel Reinforced) conductors are commonly used. 3. Line length : Can range from a few kilometers to several hundred kilometers. 4. Power capacity : Depends on the solar plant's capacity, typically ranging from 10 MW to 1000 MW. 5. Corridor selection : Carefully chosen to minimize environmental impact and ensure safety. 6. Tower design : Designed to withstand weather conditions and support conductors. 7. Insulator selection : Suitable for outdoor use and designed to withstand voltage stresses. #renewables #greenenergy #transmission #electrical #o&m

#Mechanical_Engineering #2 Solar Hot Water System Basic parts are indicated in the attached schematic diagram. In avarege, you might consider 75L Water Storage for each 1 m2 of Solar Panel with 0.02 L/s Solar Primary Flow. Solar thermal system is commonly used for energy saving.

Building a PV power plant is a dynamic undertaking, so it is crucial to pay maximum attention to the design process. This is especially important to note because the process begins with racking. Racking is not only the foundation and skeleton of the whole system, but the ability of the mounting systems and trackers to maintain a steady performance affects the entirety of the module’s lifespan. They also have to be custom-made, which makes them design-intensive. Our engineering services include expert engineers who can offer the right design advice to build industry-standard PV power plants. Please review the link in the comments section to learn more about our engineering services. #SolarPower #EngineeringServices #RenewableEnergy #QualityAssurance #CleanEnergyAssociates

IDTs Veins of solar power plant Inverter Duty Transformers (IDTs) are high-efficiency transformers used in solar power plants to convert DC energy into AC power at a low voltage. The AC power is then fed into the grid through the IDT and a Power Transformer (PT). Here are some features of IDTs: Robust construction: IDTs are built to be sturdy and have a high overload capability. Low noise and vibration: IDTs are designed to be quiet and have low vibration levels. Energy efficient: IDTs are designed to be energy efficient with low losses. Low operational cost: IDTs are designed to have a low operational cost. Earthing shield: IDTs have an earthing shield between the high voltage (HV) and low voltage (LV) windings to reduce harmonics and residual resonance. Tappings: IDTs have tappings to maintain accuracy in voltage at the secondary of the transformer.

Building a PV power plant is a dynamic undertaking, so paying maximum attention to the design process is crucial. This is especially important to note because the process begins with racking. Racking is not only the foundation and skeleton of the whole system, but the ability of the mounting systems and trackers to maintain a steady performance affects the entirety of the module’s lifespan.   They also have to be custom-made, which makes them design-intensive.   Our engineering services include expert engineers who can offer the right design advice to build industry-standard PV power plants.   Check the link in the comments section to learn more about our engineering services.    #SolarPower #EngineeringServices #RenewableEnergy #QualityAssurance #CleanEnergyAssociates 

How does Sunforson’s Grounding Clip Work?  In our solar mounting system quotation list,you can usually see one component:Grounding clip.And do you know how does it work? In order to strengthen the conductive grounding performance of photovoltaic modules and prevent lightning strikes, a grounding clip is arranged between the mid clamps and the rails.There are four conical convex points on the upper and lower sides of the grounding clip, and sharp thorns are left on the upper end.Under the action of installation pressure, the conical convex points on the upper and lower surfaces of the grounding gasket can pierce the galvanized layer on the surface of the support frame and the oxide film on the aluminum surface of the photovoltaic panel, thereby enhancing the conductivity of the photovoltaic module and grounding the photovoltaic panel. Unobstructed, eliminates the induced static electricity generated in the power generation process, and can effectively prevent lightning strikes and damage to the battery panel. For the convenience of installation, Sunforson's grounding clip is provided with two rows of flanges perpendicular to the bottom surface, and the distance between the two rows of flanges is adapted to the width of the bottom of the mid clamp. This flanging can provide the accuracy and consistency of the installation position and improve the installation efficiency. Sunforson’ssolar panel mount has high quality and effective design,welcome to contact us forsolar bracket!

Here's a step-by-step guide for solar On-Grid rooftop installation *Installation Steps:* 1. Site assessment: Evaluate rooftop suitability. 2. System design: Determine solar panel capacity. 3. Permitting: Obtain necessary permits. 4. Installation: Install solar panels, inverter, and mounting structure. 5. Commissioning: Connect to grid and test system. 6. Monitoring: Install monitoring system.

😁 A 1.5 MW Solar Power Plant Load calculation. || PV Panels Calculation. || Battery Bank. || Size Calculation of Invertor. || Area Required for PV Panels. || Sizing of Electrical Cables. #solar #pv #energy #design #electrical #electricity

  Facts about solar PV system design: 1: We have 3 types of design: electrical, mechanical, and civil in some projects. 2: Great drawings don't mean great design. 3: Great design means fewer problems in project implementation. 4: More oversizing (DC/AC ratio) doesn't always result in more energy yield.  5: The best design shouldn't be the most complex one. 6: The highest price shouldn't be the best design. 7: The more data you have, the more accuracy you will provide. #solar #PV #Saudi #energy