MonTech USA’s Post

🧪 𝗟𝗲𝘃𝗲𝗹 𝗺𝗲𝗮𝘀𝘂𝗿𝗲𝗺𝗲𝗻𝘁 𝗶𝗻 𝘁𝗵𝗲 𝗱𝗶𝘀𝗰𝗵𝗮𝗿𝗴𝗲 𝗰𝗵𝘂𝘁𝗲 𝗼𝗳 𝘁𝗵𝗲 𝗯𝗲𝗹𝘁 𝗱𝗿𝘆𝗲𝗿 The final, still wet pigment cake is heated on a belt dryer. At the end of the belt dryer, the dried coarse pigment powder is discharged into a silo ready for final milling and grinding into a fine powder. The feed through the belt dryer is controlled both by the flow through the chute and level in the silo. 💡 Recommended product 𝗩𝗘𝗚𝗔𝗣𝗨𝗟𝗦 𝟲𝗫 ✅ Reliable measurement independent of steam, dust and buildup  ✅ Encapsulated antenna system enables operation even in highly contaminated environment  ✅ Simple installation even in the tightest spaces thanks to very good signal focusing 👉🏻 Sensors for the highest safety standards – suitable for the wide variety of media in the chemical industry: https://lnkd.in/d3Pc62rU #measurementtechnology #sensors #chemicalindustry #levelmeasurement

🌟 Efficient Drying for Challenging Bulk Goods 🌟 In the U.S., manufacturers often face the challenge of drying high-moisture products both efficiently and gently. The LÖDIGE DRUVATHERM® VT Vacuum Shovel Dryer offers an ideal solution. With its high heating surface-to-volume ratio and advanced ploughshare mixing elements, it ensures optimal heat transfer and thorough, uniform mixing. This creates a mechanical fluid bed that allows effective drying at low temperatures, perfect for sensitive or difficult-to-dry materials. 💧🌡️ 🔹 Why Choose DRUVATHERM® VT Dryer? Efficiency: Vacuum technology enhances drying speed and effectiveness. Protection: Customized filters prevent product loss and protect the condenser. Flexibility: With capacities from 5 to 30,000 liters, it suits all production needs—from lab testing to large-scale manufacturing. The VT Dryer combines flexibility with top-notch efficiency and product quality, making it the preferred choice for manufacturers facing demanding drying requirements. #Lödige #VacuumShovelDryer #Manufacturing #Innovation #ProcessEngineering #BulkGoodsDrying #ProductionEfficiency

Without wheels and castors, the world stands still! Before our products are used worldwide and set the world in motion, they have to undergo a number of tests. Both the materials and our products are extensively tested in our test laboratory. For example, the maximum load capacity, starting resistance, electrical conductivity or the adhesion of polyurethane treads, which is shown in the video, can be tested on the test stands.🔧 This is how we ensure that our products meet quality standards and provide reliable mobility worldwide. 🔄 #WeInnovateMobility #QualityTesting #QualityAssurance

Disc Dryer: Elevate your drying precision with our Variable Cycle Laboratory Dryer for optimal results. Experience advanced air tech for rapid and accurate testing. Seamless transition to commercial scale with controlled temperature and humidity. #DiscDryer #AdvancedAirCirculation #LabEquipment #ProductDevelopment #EfficientTesting #SustainableDrying #TechInnovation

This machine is suitable for plastic melting test at high temperatures.

This machine is suitable for plastic melting test at high temperatures.

Are you ready for another short video? This one is a very short introduction to Low Temperature Testing of Rubber Materials. #lowtemperaturetesting

🔍 Discover an excerpt from a compelling case study showcasing the substantial savings that switching to polyurethane chocks can bring! https://hubs.ly/Q02xWFmv0 #WheelChocks #VehicleProtection #SafetyFirst

Fast, Accurate, Easy To Use, Safe! Traditionally, measuring melt temperature in injection molding can be very time consuming, inaccurate, unsafe and expensive. Measuring a purge pile with a thermocouple requires a minimum of five ounces of material, cycle interruption, heating up the thermocouple and repeating the process a minimum of three times (total of fifteen ounces) and taking the average temperature. Measuring with the MTMS Kit can be done in under 1 minute! Step 1.) Run the press to stabilize the process. Step 2.) Put the press in manual mode. Step 3.) Retract the barrel and insert the purge puck. Step 4.) Bring the barrel forward and inject ONE shot. Step 5.) Retract the barrel, remove probe/cup, and record the temperature. Why Measure Plastic Melt Temperature? According to RJG, Inc, there are four major variables that every plastic injection molder should measure: MELT TEMPERATURE, FLOW, PRESSURE, COOLING Watch RJG's Jason Robinson demonstrate the MTMS Kit https://lnkd.in/gG8-T_V5

Arkadiusz Kuta, Advanced Materials Processing Specialist at Air Products, explains how the use of nitrogen helps to improve the surface quality of materials by achieving a smooth, shiny surface, increase extrusion speed and extend dies lifetime, among many other benefits. Watch the video to find out more. https://brnw.ch/21wP0ZP