Jeremy's IT Lab’s Post

Answer: d). Passive + Active a). different etherChannel protocols. b). different etherchannel protocols c). same protocol but it will not actively try to form an EtherChannel. So no etherchannel will be formed. d). etherchannel successful formed by Link Aggregation Control Protocol (LACP). "On' only works with 'On' for Static EthernetChannel. On + On =✅️ PAgP uses Auto and Desirable mode: Auto + Auto = ❌️ Desirable + Auto =✅️ Desirable + Desirable= ✅️ LACP uses Passive and Active mode: Passive t Passive=❌️ Active + Passive=✅️ Active+ Active =✅️

📝 CCNA quiz: You issue the following commands on a switch port: 'switchport trunk native vlan 11', switchport access vlan 10', 'switchport mode access'. When an untagged frame arrives on the port, which VLAN is the frame assigned to? a) VLAN 10 b) VLAN 11 ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gtQDSbZh #cisco #ccna #jeremysitlab #jitl

📝 CCNA quiz: In which OSPF neighbor state do routers send DBD messages to describe the contents of their LSDB? a) 2-Way b) Loading c) ExStart d) Exchange ➡️ Answer & explanation on my channel's community tab: https://lnkd.in/gYC7Ks5w #cisco #ccna

📝 CCNA quiz: R1's G0/0 interface has the IP address 192,168,1,1/24. Which of the following 'network' commands can be used to activate OSPF on the interface? a) network 192,168,0,0 0,0,0,255 area 0 b) network 192,168,1,1 0,0,0,0 area 0 c) network 192,168,1,0 0,0,0,0 area 0 *I have to use commas in the IP addresses or LinkedIn interprets them as links and blocks the post 🤷♂️ ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gtQDSbZh #cisco #ccna #jeremysitlab #jitl

B. Ip routing Do this before configuring any IP routes or IP addresses on a multilayer switch so you can do layer 3 commands.

📝 CCNA quiz In which situation does an access port send and receive 802.1-Q tagged frames? a) When the native VLAN is disabled b) When a voice VLAN is configured on the port c) When the port uses 802.1X authentication d) An access port never sends and receives tagged frames ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gtQDSbZh #cisco #ccna #jeremysitlab #jitl

📝 CCNA quiz When configuring static NAT with 'ip nat inside source static <address> <address>', which two addresses do you define in the command, and in which order? a) <inside-local> <outside-global> b) <inside-local> <outside-local> c) <inside-local> <inside-global> d) <inside-global> <inside-local> ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gtQDSbZh #cisco #ccna #jeremysitlab #jitl

📝 CCNA quiz R1 is using OSPF and receives two routes to the 10,0,1,0/24 network from two different neighbors. What parameter does R1 use to determine which route to insert into its routing table? a) Metric b) AD c) Prefix length d) Most specific match *I have to use commas in the IP address or LinkedIn interprets is as a suspicious link and blocks the post 🤷♂️ ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gtQDSbZh #cisco #ccna #jeremysitlab #jitl

📝 CCNA quiz: What is the correct syntax for configuring inside source static NAT? a) ip nat inside source static <inside-local-ip> <outside-local-ip> b) ip nat inside source static <inside-global-ip> <inside-local-ip> c) ip nat inside source static <inside-local-ip> <outside-global-ip> d) ip nat inside source static <inside-local-ip> <inside-global-ip> ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gkmDY_Mg #cisco #ccna #jeremysitlab #jitl

📝 CCNA quiz: SW1 and SW2 are new switches with no VTP configurations. You configure VTP settings on SW1, causing it to send an advertisement to SW2. How does SW2 react to SW1's advertisement? a) SW2 ignores the advertisement from SW1. b) SW2 joins SW1's VTP domain. c) SW2 rejects the advertisement and sends its own VTP advertisement. d) SW2 shuts down all of its VLANs until it receives a manual configuration. ➡ Answer & explanation on my channel's community tab: https://lnkd.in/gtQDSbZh #cisco #ccna #jeremysitlab #jitl