From Bootlegging to Amphibious Assaults

Wikimedia: LCVP (United States)

The landing craft, vehicle, personnel (LCVP) or Higgins boat was a landing craft used extensively by the Allied forces in amphibious landings in World War II. Typically constructed from plywood, this shallow-draft, barge-like boat could ferry a roughly platoon-sized complement of 36 men to shore at 9 knots (17 km/h). Men generally entered the boat by climbing down a cargo net hung from the side of their troop transport; they exited by charging down the boat's lowered bow ramp.

Designer Andrew Higgins based it on boats made for operating in swamps and marshes. More than 23,358 were built, by Higgins Industries and licensees.[1][2]

Taking the last letter of the LCVP designation, sailors often nicknamed the Higgins Boat the "Papa Boat" or "Peter Boat" to differentiate it from other landing craft such as the LCU and the LCM, with the LCM being called the "Mike Boat".[3]

At just over 36 ft (11 m) long and just under 11 ft (3.4 m) wide, the LCVP was not a large craft. Powered by a 225-horsepower Gray Marine 6-71 diesel engine at a maximum speed of 12 knots, it would sway in choppy seas, causing seasickness. Since its sides and rear were made of plywood, it offered limited protection from enemy fire but also reduced cost and saved steel. The Higgins boat could hold either a 36-man platoon, a jeep and a 12-man squad, or 8,000 lb (3.6 t) of cargo. Its shallow draft (3 feet aft and 2 feet, 2 inches forward) enabled it to run up onto the shoreline, and a semi-tunnel built into its hull protected the propeller from sand and other debris. The steel ramp at the front could be lowered quickly. It was possible for the Higgins boat to swiftly disembark men and supplies, reverse itself off the beach, and return to the supply ship for another load within three to four minutes.[4]

The boat's thin armor left it vulnerable to heavier enemy fire, and it was found that extremely shallow water and hard obstructions such as reefs could stop the boat. Other vehicles such as the Landing Vehicle Tracked were later created to meet those drawbacks in amphibious operations.

The Higgins boat was built in New Orleans, Louisiana.

My Comment: The Business Case

Andrew Higgins started out in the lumber business, but gradually moved into boat building, which became his sole operation after the lumber transport company he was running entered bankruptcy in 1930. Many sources say his boats were intended for use by trappers and oil-drillers; occasionally, some sources imply or even say that Higgins intended to sell the boats to individuals intending to smuggle illegal liquor into the United States.[6][7][8]

Higgins' financial difficulties, and his association with the U.S. military, occurred around the time Prohibition was repealed, which would have ruined his market in the rum-running sector; the U.S. Navy's interest in the boats was, in any case, providential, though Higgins proved unable to manage his company's good fortune.[1]

The United States Marine Corps was always interested in finding better ways to get men across a beach in an amphibious landing. They were frustrated that the Navy's Bureau of Construction and Repair could not meet its requirements and began to express interest in Higgins' boat. When tested in 1938 by the Navy and Marine Corps, Higgins' Eureka boat surpassed the performance of a Navy-designed boat and was tested by the services during fleet landing exercises in February 1939. Satisfactory in most respects, the boat's major drawback appeared to be that equipment had to be unloaded, and men disembarked, over the sides, thus exposing them to enemy fire in combat situations and making unloading time-consuming and complex. However, that was the best available boat design, and it was put into production and service as the landing craft, personnel (large), abbreviated as LCP(L). The LCP(L) had two machine gun positions at the bow.

The LCP(L), also commonly called the "Higgins" boat, was supplied to the British (from October 1940), to whom it was initially known as the "R-boat" and used for commando raids.

The Japanese had been using ramp-bowed landing boats like Daihatsu-class landing craft in the Second Sino-Japanese War since the summer of 1937—boats that had come under intense scrutiny by Navy and Marine Corps observers at the Battle of Shanghai in particular, including from future general, Victor H. Krulak.[9] When Krulak showed Higgins a picture and suggested that Higgins develop a version of the ramped craft for the Navy, Higgins, at his own expense, started his designers working on adapting the idea to the boat design. He then had three of the craft built, again at his own expense.[10]

Men disembarking from an LCVP

On May 26, 1941, Commander Ross Daggett, from the Navy Bureau of Ships, and Major Ernest Linsert, of the Marine Corps Equipment Board, witnessed the testing of the three craft. Tests involved off-loading a truck and the embarking and disembarking of 36 Higgins employees, simulating troops. Early models were designated Landing Craft, Personnel (Ramp) or LCP(R). The LCP(R) was used in beach landings in North Africa and at Guadalcanal, Salerno and Tarawa. The Landing Craft, Personnel (Ramp) craft later was designated LCVP—Landing Craft Vehicle, Personnel.[10] By D-Day the LCVP had replaced the LCP(R).[11]

...